CN0511 Test Suite

Prerequisites:

  • Scopy v2.3.0 or later with CN0511 plugin installed

  • CN0511 board connected, or emulator running: iio-emu cn0511 <repo>/packages/cn0511/emu-xml/cn0511.xml (URI: ip:127.0.0.1)

  • Device drivers and firmware are up to date

Test 1: Plugin Loads

UID: TST.CN0511.PLUGIN_LOADS

RBP: P0

Description: Verify that the CN0511 plugin loads in Scopy and the tool is accessible.

OS: ANY

Preconditions:

  • Scopy is installed

  • CN0511 board is connected or the CN0511 emulator is running

Steps:
  1. Open Scopy and connect to the CN0511 device or emulator

    • Expected result: Scopy connects without errors and the CN0511 tool appears in the tool list

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 2: Single Tone Mode Section Visible

UID: TST.CN0511.SINGLE_TONE_SECTION_VISIBLE

RBP: P1

Description: Verify that the Single Tone Mode section displays the Frequency spinbox, Amplitude spinbox, and Enter button.

OS: ANY

Preconditions:

  • CN0511 tool is open

Steps:
  1. Observe the Single Tone Mode section

    • Expected result: The section shows a Frequency (MHz) spinbox with default value 4500, an Amplitude (dBm) spinbox with default value 0, and an Enter button

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 3: Set Output Frequency

UID: TST.CN0511.SET_FREQUENCY

RBP: P1

Description: Verify that setting a new frequency value and clicking Enter writes the frequency to the AD9166 DAC without errors.

OS: ANY

Preconditions:

  • CN0511 tool is open

Steps:
  1. Set Frequency (MHz) to 2000

    • Expected result: The spinbox accepts the value 2000

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 4: Set Output Amplitude

UID: TST.CN0511.SET_AMPLITUDE

RBP: P1

Description: Verify that setting a new amplitude value and clicking Enter writes the amplitude to the AD9166 DAC without errors.

OS: ANY

Preconditions:

  • CN0511 tool is open

Steps:
  1. Set Amplitude (dBm) to -20

    • Expected result: The spinbox accepts the value -20

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 5: DAC Amplifier Enable

UID: TST.CN0511.DAC_AMP_ENABLE

RBP: P1

Description: Verify that the DAC Amplifier section is visible and that toggling the Enable checkbox writes the en attribute to the ad9166-amp device.

OS: ANY

Preconditions:

  • CN0511 tool is open

Steps:
  1. Observe the DAC Amplifier section

    • Expected result: The section displays an Enable checkbox

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 6: Refresh Reads NCO Frequency

UID: TST.CN0511.REFRESH_READS_FREQUENCY

RBP: P1

Description: Verify that clicking the Refresh button reads the current NCO frequency from the device and updates the Frequency spinbox.

OS: ANY

Preconditions:

  • CN0511 tool is open

Steps:
  1. Set Frequency (MHz) to 3000 and click Enter

    • Expected result: Calibration is applied without error

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 7: Verify Output Frequency with AD936x Receiver

UID: TST.CN0511.VERIFY_FREQUENCY_WITH_AD936X

RBP: P2

Description: Verify that the CN0511 RF output is present at the configured frequency by receiving it with a connected AD936x-based device (e.g., PlutoSDR or AD-FMCOMMS) using the AD936x plugin.

OS: ANY

Preconditions:

  • CN0511 board is connected (emulator cannot be used for this test)

  • A PlutoSDR or AD-FMCOMMS board is connected to the same host

  • CN0511 RF SMA output is connected to the AD936x board RX SMA input via coaxial cable

  • Both devices are visible in Scopy

Steps:
  1. Open the CN0511 tool, set Frequency (MHz) to 1000, Amplitude (dBm) to -10, and click Enter

    • Expected result: Calibration is applied; CN0511 is transmitting at 1000 MHz

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL