no-OS
|
Basic example header file for lt7182s project. More...
Go to the source code of this file.
Functions | |
int | basic_example_main () |
basic example main execution. More... | |
Basic example header file for lt7182s project.
Copyright 2024(c) Analog Devices, Inc.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES, INC. “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ANALOG DEVICES, INC. BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
int basic_example_main | ( | ) |
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
basic example main execution.
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.
GPIO Pin Interrupt Controller
Parameter to be passed when the callback is called.
GPIO Pin Interrupt Controller
MAX14906 Initialization
Setting SLED set bit 1 in the config register.
Turning the Status LEDs on, then off.
Setting a current limit for channel 0.
Read current limit for all channels.
Setting the on state for channel 0, and then verifying it.
Maximum value of 3V.
The increment of the AO1 to be used (needs to be smaller then the SR step-size).
Frequency of the signal.
Initializing GPIO 0 of MAX22017.
Setting its value to HIGH.
Changing operation mode of MAX22017.
Changing configuration of MAX22017.
Changing slew-rate configuration of MAX22017.
Reading the GAIN correction.