U-Boot Falcon Mode Example

Introduction

This page provides instructions for using U-Boot Falcon Mode and ADI Fastboot on ADSP-SC59x boards.

Note

The Falcon Mode feature is supported on Linux for ADSP-SC5xx Processors version 3.0.0 and later, and on SC59x platforms.

What is Falcon Mode?

Falcon Mode is a U-Boot feature that shortens boot time by allowing the Secondary Program Loader (SPL) to boot the Linux kernel directly, bypassing the full U-Boot bootloader. For more details, see the U-Boot Falcon Mode documentation.

Requirements

  • Linux for ADSP-SC5xx Processors version 3.0.0 or later

  • ADSP-SC59x development board

Building U-Boot with Falcon Mode

Step 1: Configure Build System

After following the Getting Started guides and sourcing the setup script:

source setup-environment -m adsp-sc598-som-ezkit

A build folder and local configuration file will be created at $PROJECT_DIR/build/conf/local.conf.

Step 2: Enable Falcon Mode

Edit conf/local.conf and append the following lines:

MACHINE_FEATURES:remove = " spl"
MACHINE_FEATURES:append = " falcon"

Step 3: Build and Flash

Proceed with building and flashing the image as described in the Getting Started guides.

Booting with Falcon Mode

Default Falcon Mode Behavior

When U-Boot with Falcon Mode support is flashed onto the board, the default behavior is to boot directly from SPL using the configured boot method (typically SPI boot):

U-Boot SPL 2020.10 (Apr 12 2023 - 18:48:14 +0000)
ADI Boot Mode: 0x1 (QSPI Master)
Trying to boot from SPI
## Loading kernel from FIT Image at 96000000 ...
   Using 'conf-1' configuration
   Verifying Hash Integrity ... OK
   Trying 'kernel-1' kernel subimage
Verifying Hash Integrity ... sha1+ sha1,rsa2048:dev- OK
   Loading kernel from 0x960000e0 to 0x9a200000
   Uncompressing Kernel Image
## Loading ramdisk from FIT Image at 96000000 ...
   Using 'conf-1' configuration
   Verifying Hash Integrity ... OK
   Trying 'ramdisk-3' ramdisk subimage
   Verifying Hash Integrity ... sha1+ sha1,rsa2048:dev- OK
   Loading ramdisk from 0x965a1e50 to 0x9c000000
## Loading fdt from FIT Image at 96000000 ...
   Using 'conf-1' configuration
   Verifying Hash Integrity ... OK
   Trying 'fdt-2' fdt subimage
   Verifying Hash Integrity ... sha1+ sha1,rsa2048:dev- OK
   Loading fdt from 0x9659ac00 to 0x99000000
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.000000] Linux version 5.15.78-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-musl-gcc (GCC) 11.2.0, GNU ld (GNU Binutils) 2.38.20220313) #1 SMP PREEMPT Wed Apr 12 17:53:07 UTC 2023
[    0.000000] Machine model: ADI 64-bit SC598 SOM EZ Kit
[    0.000000] earlycon: adi_uart0 at MMIO 0x0000000031003000 (options '')
[    0.000000] printk: bootconsole [adi_uart0] enabled
[    0.000000] efi: UEFI not found.

Fallback to U-Boot Proper

You can bypass Falcon Mode and fall back to full U-Boot by holding down the push button PB1 on the carrier board during reset/boot:

U-Boot SPL 2020.10 (Apr 12 2023 - 18:48:14 +0000)
Pushbutton helding during boot -- entering U-Boot ProperADI Boot Mode: 0x1 (QSPI Master)
Trying to boot from BOOTROM


U-Boot 2020.10 (Apr 12 2023 - 18:48:14 +0000)

CPU:   ADSP ADSP-SC598-0.0 (spi slave boot)
Model: ADI sc598-som-ezkit
DRAM:  224 MiB
WDT:   Not found!
MMC:   mmc@310C7000: 0
Loading Environment from SPIFlash... SF: Detected is25lp512 with page size 256 Bytes, erase size 64 KiB, total 64 MiB
OK
In:    serial@0x31003000
Out:   serial@0x31003000
Err:   serial@0x31003000
Net:   eth0: eth0
Hit any key to stop autoboot:  0

ADI Fastboot

Overview

Yocto release 5.0.0 introduces ADI Fastboot, which combines U-Boot Falcon Mode with kernel modifications to achieve the fastest possible boot times, enabling hardware initialization and userspace application execution with minimal delay.

Currently supported boards:

  • ADSP-SC598-SOM-EZKIT

U-Boot Configuration

SOMs with the EZKIT carrier default to using OSPI flash (device 0 on bus 0) for booting, instead of the standard QSPI configuration present on the SOM. This is coupled with DMA and maximum clock frequencies to achieve extremely fast transactions.

Flash the OSPI on the EZKIT carrier via U-Boot. Once U-Boot is loaded via GDB, execute:

=> run update_spi_uboot_only
=> setenv sfdev 0:0; run update_spi_fit

This will flash U-Boot to QSPI and the fitImage to OSPI.

Kernel Configuration

The Linux kernel has been trimmed to achieve minimal boot time. The following drivers and devices are disabled:

  • Crypto (CRC and PKTE)

  • SHARC (both cores and remoteproc)

  • eMMC

  • QSPI

  • USB

  • gptimers

  • TRU

  • HADC

  • SPORT

  • Ethernet

  • SRAM

  • Watchdog

Expected Boot Output

The following is example kernel boot output for ADI Fastboot:

[2025-08-08 12:17:04.393] ADI Boot Mode: 0x1 (QSPI Master)
[2025-08-08 12:17:04.398] Trying to boot from SPI
[2025-08-08 12:17:04.398] Probe @41666666Hz
[2025-08-08 12:17:04.415] ?6
[2025-08-08 12:17:04.513] Read ID via 1x SPI: c2 85 3b
[2025-08-08 12:17:04.513] Configure MX66LM1G45: OPI DTR = on
[2025-08-08 12:17:04.519] Read ID via 8x OPI+DTR: c2 85 3b
[2025-08-08 12:17:04.519]       Success: ID Match!
[2025-08-08 12:17:04.519] Configuration Register 2(0x0): 2
[2025-08-08 12:17:04.524]       Success: In DTR OPI Mode!
[2025-08-08 12:17:04.524] ## Loading kernel from FIT Image at 96000000 ...
[2025-08-08 12:17:04.530]    Using 'conf-1' configuration
[2025-08-08 12:17:04.536]    Trying 'kernel-1' kernel subimage
[2025-08-08 12:17:04.536]    Loading kernel from 0x960000e0 to 0x9a200000
[2025-08-08 12:17:04.541]    Uncompressing Kernel Image
[2025-08-08 12:17:06.332] ## Loading ramdisk from FIT Image at 96000000 ...
[2025-08-08 12:17:06.332]    Using 'conf-1' configuration
[2025-08-08 12:17:06.338]    Trying 'ramdisk-3' ramdisk subimage
[2025-08-08 12:17:06.338]    Loading ramdisk from 0x963f63b8 to 0x9c000000
[2025-08-08 12:17:06.383] ## Loading fdt from FIT Image at 96000000 ...
[2025-08-08 12:17:06.383]    Using 'conf-1' configuration
[2025-08-08 12:17:06.388]    Trying 'fdt-2' fdt subimage
[2025-08-08 12:17:06.388]    Loading fdt from 0x963ef428 to 0x99000000
[2025-08-08 12:17:06.442] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[2025-08-08 12:17:06.442] Linux version 6.12.0-yocto-standard-00079-g89984f318ee7 (oe-user@oe-host) (aarch64-adi_glibc-linux-gcc (GCC) 13.2.0, GNU ld (GNU Binutils) 2.40.0.20230214) #1 SMP PREEMPT Thu Aug  8 12:02:01 UTC 2025
[2025-08-08 12:17:06.464] Machine model: ADI 64-bit SC598 SOM EZ Kit
[2025-08-08 12:17:06.464] earlycon: adi_uart0 at MMIO 0x0000000031003000 (options '')
[2025-08-08 12:17:06.470] printk: legacy bootconsole [adi_uart0] enabled
[2025-08-08 12:17:06.476] efi: UEFI not found.
[2025-08-08 12:17:06.476] OF: reserved mem: 0x0000000020000000..0x00000000200003ff (1 KiB) nomap non-reusable rsc_tbl0@20000000
[2025-08-08 12:17:06.487] OF: reserved mem: 0x0000000020000400..0x00000000200007ff (1 KiB) nomap non-reusable rsc_tbl0@20000400
[2025-08-08 12:17:06.493] OF: reserved mem: 0x0000000020005000..0x0000000020024fff (128 KiB) nomap non-reusable sharc_internal_icc@20005000
[2025-08-08 12:17:06.504] OF: reserved mem: 0x0000000020040000..0x000000002007ffff (256 KiB) map non-reusable sram1-reserved@20040000
[2025-08-08 12:17:06.515] OF: reserved mem: 0x0000000020080000..0x0000000020083fff (16 KiB) nomap non-reusable vdev0vring0@20080000
[2025-08-08 12:17:06.526] Reserved memory: created DMA memory pool at 0x0000000020084000, size 0 MiB
[2025-08-08 12:17:06.532] OF: reserved mem: initialized node vdev0buffer@20084000, compatible id shared-dma-pool
[2025-08-08 12:17:06.537] OF: reserved mem: 0x0000000020084000..0x00000000200a3fff (128 KiB) nomap non-reusable vdev0buffer@20084000
[2025-08-08 12:17:06.548] OF: reserved mem: 0x00000000200a4000..0x00000000200a7fff (16 KiB) nomap non-reusable vdev0vring0@200A4000
[2025-08-08 12:17:06.560] Reserved memory: created DMA memory pool at 0x00000000200a8000, size 0 MiB
[2025-08-08 12:17:06.565] OF: reserved mem: initialized node vdev0buffer@200A8000, compatible id shared-dma-pool
[2025-08-08 12:17:06.570] OF: reserved mem: 0x00000000200a8000..0x00000000200c7fff (128 KiB) nomap non-reusable vdev0buffer@200A8000
[2025-08-08 12:17:06.588] NUMA: Faking a node at [mem 0x0000000020040000-0x000000009dffffff]
[2025-08-08 12:17:06.594] NODE_DATA(0) allocated [mem 0x9df60480-0x9df626bf]
[2025-08-08 12:17:06.594] Zone ranges:
[2025-08-08 12:17:06.599]   DMA      [mem 0x0000000020040000-0x000000009dffffff]
[2025-08-08 12:17:06.599]   DMA32    empty
[2025-08-08 12:17:06.605]   Normal   empty
[2025-08-08 12:17:06.605] Movable zone start for each node
[2025-08-08 12:17:06.610] Early memory node ranges
[2025-08-08 12:17:06.610]   node   0: [mem 0x0000000020040000-0x000000002007ffff]
[2025-08-08 12:17:06.616]   node   0: [mem 0x0000000090000000-0x000000009dffffff]
[2025-08-08 12:17:06.621] Initmem setup node 0 [mem 0x0000000020040000-0x000000009dffffff]
[2025-08-08 12:17:06.627] On node 0, zone DMA: 64 pages in unavailable ranges
[2025-08-08 12:17:06.649] On node 0, zone DMA: 32640 pages in unavailable ranges
[2025-08-08 12:17:06.655] On node 0, zone DMA: 8192 pages in unavailable ranges
[2025-08-08 12:17:06.655] percpu: Embedded 29 pages/cpu s78176 r8192 d32416 u118784
[2025-08-08 12:17:06.661] Detected VIPT I-cache on CPU0
[2025-08-08 12:17:06.666] CPU features: detected: GIC system register CPU interface
[2025-08-08 12:17:06.672] CPU features: detected: Virtualization Host Extensions
[2025-08-08 12:17:06.677] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[2025-08-08 12:17:06.683] alternatives: applying boot alternatives
[2025-08-08 12:17:06.683] Kernel command line: earlycon=adi_uart,0x31003000 console=ttySC0,115200 vmalloc=512M
[2025-08-08 12:17:06.694] Unknown kernel command line parameters "vmalloc=512M", will be passed to user space.
[2025-08-08 12:17:06.700] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[2025-08-08 12:17:06.706] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[2025-08-08 12:17:06.711] Fallback order for Node 0: 0
[2025-08-08 12:17:06.717] Built 1 zonelists, mobility grouping on.  Total pages: 57408
[2025-08-08 12:17:06.722] Policy zone: DMA
[2025-08-08 12:17:06.722] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
[2025-08-08 12:17:06.728] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
[2025-08-08 12:17:06.734] software IO TLB: area num 1.
[2025-08-08 12:17:06.734] software IO TLB: mapped [mem 0x000000009de8d000-0x000000009decd000] (0MB)
[2025-08-08 12:17:06.761] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[2025-08-08 12:17:06.761] trace event string verifier disabled
[2025-08-08 12:17:06.767] rcu: Preemptible hierarchical RCU implementation.
[2025-08-08 12:17:06.772] rcu:  RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=1.
[2025-08-08 12:17:06.778]       Trampoline variant of Tasks RCU enabled.
[2025-08-08 12:17:06.778] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[2025-08-08 12:17:06.789] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[2025-08-08 12:17:06.795] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[2025-08-08 12:17:06.806] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[2025-08-08 12:17:06.812] GICv3: GIC: Using split EOI/Deactivate mode
[2025-08-08 12:17:06.812] GICv3: 384 SPIs implemented
[2025-08-08 12:17:06.812] GICv3: 0 Extended SPIs implemented
[2025-08-08 12:17:06.817] Root IRQ handler: gic_handle_irq
[2025-08-08 12:17:06.822] GICv3: GICv3 features: 16 PPIs
[2025-08-08 12:17:06.822] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0
[2025-08-08 12:17:06.828] GICv3: CPU0: found redistributor 0 region 0:0x0000000031240000
[2025-08-08 12:17:06.833] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[2025-08-08 12:17:06.840] arch_timer: cp15 timer(s) running at 31.25MHz (phys).
[2025-08-08 12:17:06.840] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314 ns
[2025-08-08 12:17:06.851] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns
[2025-08-08 12:17:06.857] clocksource: cs_adi_gptimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 15290083572 ns
[2025-08-08 12:17:06.868] sched_clock: 32 bits at 125MHz, resolution 8ns, wraps every 17179869180ns
[2025-08-08 12:17:06.874] Console: colour dummy device 80x25
[2025-08-08 12:17:06.880] Calibrating delay loop (skipped), value calculated using timer frequency.. 62.50 BogoMIPS (lpj=125000)
[2025-08-08 12:17:06.885] pid_max: default: 32768 minimum: 301
[2025-08-08 12:17:06.891] LSM: initializing lsm=capability
[2025-08-08 12:17:06.891] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[2025-08-08 12:17:06.896] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[2025-08-08 12:17:06.910] cacheinfo: Unable to detect cache hierarchy for CPU 0
[2025-08-08 12:17:06.910] rcu: Hierarchical SRCU implementation.
[2025-08-08 12:17:06.915] rcu:  Max phase no-delay instances is 1000.
[2025-08-08 12:17:06.921] EFI services will not be available.
[2025-08-08 12:17:06.921] smp: Bringing up secondary CPUs ...
[2025-08-08 12:17:06.927] smp: Brought up 1 node, 1 CPU
[2025-08-08 12:17:06.927] SMP: Total of 1 processors activated.
[2025-08-08 12:17:06.939] CPU: All CPU(s) started at EL2
[2025-08-08 12:17:06.939] CPU features: detected: 32-bit EL0 Support
[2025-08-08 12:17:06.939] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[2025-08-08 12:17:06.949] CPU features: detected: CRC32 instructions
[2025-08-08 12:17:06.949] CPU features: detected: RCpc load-acquire (LDAPR)
[2025-08-08 12:17:06.955] CPU features: detected: LSE atomic instructions
[2025-08-08 12:17:06.960] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[2025-08-08 12:17:06.966] alternatives: applying system-wide alternatives
[2025-08-08 12:17:06.972] Memory: 206140K/229632K available (5568K kernel code, 812K rwdata, 1892K rodata, 1856K init, 479K bss, 21468K reserved, 0K cma-reserved)
[2025-08-08 12:17:06.984] devtmpfs: initialized
[2025-08-08 12:17:06.993] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[2025-08-08 12:17:06.999] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[2025-08-08 12:17:07.004] 30064 pages in range for non-PLT usage
[2025-08-08 12:17:07.010] 521584 pages in range for PLT usage
[2025-08-08 12:17:07.010] pinctrl core: initialized pinctrl subsystem
[2025-08-08 12:17:07.016] DMI not present or invalid.
[2025-08-08 12:17:07.016] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[2025-08-08 12:17:07.022] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[2025-08-08 12:17:07.033] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[2025-08-08 12:17:07.039] thermal_sys: Registered thermal governor 'step_wise'
[2025-08-08 12:17:07.045] cpuidle: using governor menu
[2025-08-08 12:17:07.045] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[2025-08-08 12:17:07.050] ASID allocator initialised with 65536 entries
[2025-08-08 12:17:07.057] Serial: AMBA PL011 UART driver
[2025-08-08 12:17:07.084] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[2025-08-08 12:17:07.097] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
[2025-08-08 12:17:07.106] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
[2025-08-08 12:17:07.115] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
[2025-08-08 12:17:07.124] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[2025-08-08 12:17:07.138] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
[2025-08-08 12:17:07.138] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
[2025-08-08 12:17:07.143] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
[2025-08-08 12:17:07.150] ACPI: Interpreter disabled.
[2025-08-08 12:17:07.156] iommu: Default domain type: Translated
[2025-08-08 12:17:07.156] iommu: DMA domain TLB invalidation policy: strict mode
[2025-08-08 12:17:07.162] usbcore: registered new interface driver usbfs
[2025-08-08 12:17:07.167] usbcore: registered new interface driver hub
[2025-08-08 12:17:07.173] usbcore: registered new device driver usb
[2025-08-08 12:17:07.173] i2c-adi-twi 31001400.twi: ADI on-chip I2C TWI Controller, regs_base@(____ptrval____)
[2025-08-08 12:17:07.198] i2c-adi-twi 31001600.twi: ADI on-chip I2C TWI Controller, regs_base@(____ptrval____)
[2025-08-08 12:17:07.204] clocksource: Switched to clocksource arch_sys_counter
[2025-08-08 12:17:07.210] VFS: Disk quotas dquot_6.6.0
[2025-08-08 12:17:07.210] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[2025-08-08 12:17:07.220] pnp: PnP ACPI: disabled
[2025-08-08 12:17:07.230] Unpacking initramfs...
[2025-08-08 12:17:07.241] workingset: timestamp_bits=42 max_order=16 bucket_order=0
[2025-08-08 12:17:07.333] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[2025-08-08 12:17:07.350] io scheduler mq-deadline registered
[2025-08-08 12:17:07.350] io scheduler kyber registered
[2025-08-08 12:17:07.364] adi-dma 31022000.dma: Creating new peripheral DMA controller instance
[2025-08-08 12:17:07.380] adi-dma 31023000.dma: Creating new peripheral DMA controller instance
[2025-08-08 12:17:07.396] adi-dma 3102d000.dma: Creating new peripheral DMA controller instance
[2025-08-08 12:17:07.419] adi-dma 310a7000.dma: Creating new peripheral DMA controller instance
[2025-08-08 12:17:07.436] adi-dma 31026000.dma: Creating new peripheral DMA controller instance
[2025-08-08 12:17:07.462] adi-dma 3109a000.dma: Creating new MDMA controller instance
[2025-08-08 12:17:07.477] adi-trigger-routing-unit 3108a000.tru: Connecting master 134 to slave 160
[2025-08-08 12:17:07.494] adi-trigger-routing-unit 3108a000.tru: Connecting master 135 to slave 164
[2025-08-08 12:17:07.506] adi-trigger-routing-unit 3108a000.tru: Connecting master 136 to slave 168
[2025-08-08 12:17:07.528] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[2025-08-08 12:17:07.539] ADI serial driver
[2025-08-08 12:17:07.546] adi-uart4 31003000.uart: Serial probe
[2025-08-08 12:17:07.553] Freeing initrd memory: 2800K
[2025-08-08 12:17:07.553] 31003000.uart: ttySC0 at MMIO 0x0 (irq = 0, base_baud = 7812500) is a ADI-UART4
[2025-08-08 12:17:07.558] printk: legacy console [ttySC0] enabled
[2025-08-08 12:17:07.564] printk: legacy console [ttySC0] enabled
[2025-08-08 12:17:07.569] printk: legacy bootconsole [adi_uart0] disabled
[2025-08-08 12:17:07.569] printk: legacy bootconsole [adi_uart0] disabled
[2025-08-08 12:17:07.593] adi-spi3 31030000.spi: registered ADI SPI controller spi2
[2025-08-08 12:17:07.593] VFIO - User Level meta-driver version: 0.3
[2025-08-08 12:17:07.599] input: adp5587 as /devices/platform/scb/31001600.twi/i2c-1/1-0034/input/input0
[2025-08-08 12:17:07.626] adp5588_keys 1-0034: Rev.4 controller
[2025-08-08 12:17:07.626] i2c_dev: i2c /dev entries driver
[2025-08-08 12:17:07.635] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 (0,8000003f) counters available
[2025-08-08 12:17:07.656] Demotion targets for Node 0: null
[2025-08-08 12:17:07.665] adsp-sru-ctrl 310ca000.sru-ctrl-dai1: Started without extended selection codes (SC573, SC584, SC589)
[2025-08-08 12:17:07.672] clk: Disabling unused clocks
[2025-08-08 12:17:07.678] PM: genpd: Disabling unused power domains
[2025-08-08 12:17:07.685] Freeing unused kernel memory: 1856K
[2025-08-08 12:17:07.685] Run /init as init process
[2025-08-08 12:17:07.772]
[2025-08-08 12:17:07.772]          Analog Initial Ram Filesystem
[2025-08-08 12:17:07.772]                 www.analog.com
[2025-08-08 12:17:07.777]               www.yoctoproject.org
[2025-08-08 12:17:07.777]
[2025-08-08 12:17:07.777] Analog [Initramfs]: Preparing Operating System....
[2025-08-08 12:17:07.783] Analog [Initramfs]: Mounting Root File System...
[2025-08-08 12:17:07.804] Analog [Initramfs]: No root device found, dropping to getty
[2025-08-08 12:17:07.821] udhcpc: socket: Function not implemented
[2025-08-08 12:17:07.929]
[2025-08-08 12:17:07.929] adsp-sc598-som-ezkit login:

Expected boot time: Approximately 3-4 seconds after powering on or resetting the board.

References