Modules

Here is a list of all modules:

[detail level 123]

►Analog to Digital Converter (ADC)
►ADC_Registers	Registers, Bit Masks and Bit Positions for the ADC Peripheral Module
Register Offsets	ADC Peripheral Register Offsets from the ADC Base Peripheral Address
ADC_CTRL	ADC Control
ADC_STATUS	ADC Status
ADC_DATA	ADC Output Data
ADC_INTR	ADC Interrupt Control Register
ADC_LIMIT	ADC Limit
►AES
►AES_Registers	Registers, Bit Masks and Bit Positions for the AES Peripheral Module
Register Offsets	AES Peripheral Register Offsets from the AES Base Peripheral Address
AES_CTRL	AES Control Register
AES_STATUS	AES Status Register
AES_INTFL	AES Interrupt Flag Register
AES_INTEN	AES Interrupt Enable Register
AES_FIFO	AES Data Register
►AESKEYS_Registers	Registers, Bit Masks and Bit Positions for the AESKEYS Peripheral Module
Register Offsets	AESKEYS Peripheral Register Offsets from the AESKEYS Base Peripheral Address
►CRC
►CRC_Registers	Registers, Bit Masks and Bit Positions for the CRC Peripheral Module
Register Offsets	CRC Peripheral Register Offsets from the CRC Base Peripheral Address
CRC_CTRL	CRC Control
CRC_DATAIN32	CRC Data Input
CRC_DATAIN16	CRC Data Input
CRC_DATAIN8	CRC Data Input
CRC_POLY	CRC Polynomial
CRC_VAL	Current CRC Value
►Direct Memory Access (DMA)
►DMA_Registers	Registers, Bit Masks and Bit Positions for the DMA Peripheral Module
Register Offsets	DMA Peripheral Register Offsets from the DMA Base Peripheral Address
DMA_INTEN	DMA Control Register
DMA_INTFL	DMA Interrupt Register
DMA_CTRL	DMA Channel Control Register
DMA_STATUS	DMA Channel Status Register
DMA_SRC	Source Device Address. If SRCINC=1, the counter bits are incremented by 1,2, or 4, depending on the data width of each AHB cycle. For peripheral transfers, some or all of the actual address bits are fixed. If SRCINC=0, this register remains constant. In the case where a count-to-zero condition occurs while RLDEN=1, the register is reloaded with the contents of DMA_SRC_RLD
DMA_DST	Destination Device Address. For peripheral transfers, some or all of the actual address bits are fixed. If DSTINC=1, this register is incremented on every AHB write out of the DMA FIFO. They are incremented by 1, 2, or 4, depending on the data width of each AHB cycle. In the case where a count-to-zero condition occurs while RLDEN=1, the register is reloaded with DMA_DST_RLD
DMA_CNT	DMA Counter. The user loads this register with the number of bytes to transfer. This counter decreases on every AHB cycle into the DMA FIFO. The decrement will be 1, 2, or 4 depending on the data width of each AHB cycle. When the counter reaches 0, a count-to-zero condition is triggered
DMA_SRCRLD	Source Address Reload Value. The value of this register is loaded into DMA0_SRC upon a count-to-zero condition
DMA_DSTRLD	Destination Address Reload Value. The value of this register is loaded into DMA0_DST upon a count-to-zero condition
DMA_CNTRLD	DMA Channel Count Reload Register
►Flash Controller (FLC)
►FLC_Registers	Registers, Bit Masks and Bit Positions for the FLC Peripheral Module
Register Offsets	FLC Peripheral Register Offsets from the FLC Base Peripheral Address
FLC_ADDR	Flash Write Address
FLC_CLKDIV	Flash Clock Divide. The clock (PLL0) is divided by this value to generate a 1 MHz clock for Flash controller
FLC_CTRL	Flash Control Register
FLC_INTR	Flash Interrupt Register
FLC_ECCDATA	ECC Data Register
FLC_DATA	Flash Write Data
FLC_ACTRL	Access Control Register. Writing the ACTRL register with the following values in the order shown, allows read and write access to the system and user Information block: pflc-actrl = 0x3a7f5ca3; pflc-actrl = 0xa1e34f20; pflc-actrl = 0x9608b2c1. When unlocked, a write of any word will disable access to system and user information block. Readback of this register is always zero
FLC_WELR0	WELR0
FLC_WELR1	WELR1
FLC_RLR0	RLR0
FLC_RLR1	RLR1
►General-Purpose Input/Output (GPIO)
►Port and Pin Definitions
Port Definitions
Pin Definitions
►GPIO_Registers	Registers, Bit Masks and Bit Positions for the GPIO Peripheral Module
Register Offsets	GPIO Peripheral Register Offsets from the GPIO Base Peripheral Address
GPIO_EN0	GPIO Function Enable Register. Each bit controls the GPIO_EN setting for one GPIO pin on the associated port
GPIO_EN0_SET	GPIO Set Function Enable Register. Writing a 1 to one or more bits in this register sets the bits in the same positions in GPIO_EN to 1, without affecting other bits in that register
GPIO_EN0_CLR	GPIO Clear Function Enable Register. Writing a 1 to one or more bits in this register clears the bits in the same positions in GPIO_EN to 0, without affecting other bits in that register
GPIO_OUTEN	GPIO Output Enable Register. Each bit controls the GPIO_OUT_EN setting for one GPIO pin in the associated port
GPIO_OUTEN_SET	GPIO Output Enable Set Function Enable Register. Writing a 1 to one or more bits in this register sets the bits in the same positions in GPIO_OUT_EN to 1, without affecting other bits in that register
GPIO_OUTEN_CLR	GPIO Output Enable Clear Function Enable Register. Writing a 1 to one or more bits in this register clears the bits in the same positions in GPIO_OUT_EN to 0, without affecting other bits in that register
GPIO_OUT	GPIO Output Register. Each bit controls the GPIO_OUT setting for one pin in the associated port. This register can be written either directly, or by using the GPIO_OUT_SET and GPIO_OUT_CLR registers
GPIO_OUT_SET	GPIO Output Set. Writing a 1 to one or more bits in this register sets the bits in the same positions in GPIO_OUT to 1, without affecting other bits in that register
GPIO_OUT_CLR	GPIO Output Clear. Writing a 1 to one or more bits in this register clears the bits in the same positions in GPIO_OUT to 0, without affecting other bits in that register
GPIO_IN	GPIO Input Register. Read-only register to read from the logic states of the GPIO pins on this port
GPIO_INTMODE	GPIO Interrupt Mode Register. Each bit in this register controls the interrupt mode setting for the associated GPIO pin on this port
GPIO_INTPOL	GPIO Interrupt Polarity Register. Each bit in this register controls the interrupt polarity setting for one GPIO pin in the associated port
GPIO_INTEN	GPIO Interrupt Enable Register. Each bit in this register controls the GPIO interrupt enable for the associated pin on the GPIO port
GPIO_INTEN_SET	GPIO Interrupt Enable Set. Writing a 1 to one or more bits in this register sets the bits in the same positions in GPIO_INT_EN to 1, without affecting other bits in that register
GPIO_INTEN_CLR	GPIO Interrupt Enable Clear. Writing a 1 to one or more bits in this register clears the bits in the same positions in GPIO_INT_EN to 0, without affecting other bits in that register
GPIO_INTFL	GPIO Interrupt Status Register. Each bit in this register contains the pending interrupt status for the associated GPIO pin in this port
GPIO_INTFL_CLR	GPIO Status Clear. Writing a 1 to one or more bits in this register clears the bits in the same positions in GPIO_INT_STAT to 0, without affecting other bits in that register
GPIO_WKEN	GPIO Wake Enable Register. Each bit in this register controls the PMU wakeup enable for the associated GPIO pin in this port
GPIO_WKEN_SET	GPIO Wake Enable Set. Writing a 1 to one or more bits in this register sets the bits in the same positions in GPIO_WAKE_EN to 1, without affecting other bits in that register
GPIO_WKEN_CLR	GPIO Wake Enable Clear. Writing a 1 to one or more bits in this register clears the bits in the same positions in GPIO_WAKE_EN to 0, without affecting other bits in that register
GPIO_DUALEDGE	GPIO Interrupt Dual Edge Mode Register. Each bit in this register selects dual edge mode for the associated GPIO pin in this port
GPIO_PADCTRL0	GPIO Input Mode Config 1. Each bit in this register enables the weak pull-up for the associated GPIO pin in this port
GPIO_PADCTRL1	GPIO Input Mode Config 2. Each bit in this register enables the weak pull-up for the associated GPIO pin in this port
GPIO_EN1	GPIO Alternate Function Enable Register. Each bit in this register selects between primary/secondary functions for the associated GPIO pin in this port
GPIO_EN1_SET	GPIO Alternate Function Set. Writing a 1 to one or more bits in this register sets the bits in the same positions in GPIO_EN1 to 1, without affecting other bits in that register
GPIO_EN1_CLR	GPIO Alternate Function Clear. Writing a 1 to one or more bits in this register clears the bits in the same positions in GPIO_EN1 to 0, without affecting other bits in that register
GPIO_EN2	GPIO Alternate Function Enable Register. Each bit in this register selects between primary/secondary functions for the associated GPIO pin in this port
GPIO_EN2_SET	GPIO Alternate Function 2 Set. Writing a 1 to one or more bits in this register sets the bits in the same positions in GPIO_EN2 to 1, without affecting other bits in that register
GPIO_EN2_CLR	GPIO Wake Alternate Function Clear. Writing a 1 to one or more bits in this register clears the bits in the same positions in GPIO_EN2 to 0, without affecting other bits in that register
GPIO_HYSEN	GPIO Input Hysteresis Enable
GPIO_SRSEL	GPIO Slew Rate Enable Register
GPIO_DS0	GPIO Drive Strength Register. Each bit in this register selects the drive strength for the associated GPIO pin in this port. Refer to the Datasheet for sink/source current of GPIO pins in each mode
GPIO_DS1	GPIO Drive Strength 1 Register. Each bit in this register selects the drive strength for the associated GPIO pin in this port. Refer to the Datasheet for sink/source current of GPIO pins in each mode
GPIO_PS	GPIO Pull Select Mode
GPIO_VSSEL	GPIO Voltage Select
►I2C
►I2C_Registers	Registers, Bit Masks and Bit Positions for the I2C Peripheral Module
Register Offsets	I2C Peripheral Register Offsets from the I2C Base Peripheral Address
I2C_CTRL	Control Register0
I2C_STATUS	Status Register
I2C_INTFL0	Interrupt Status Register
I2C_INTEN0	Interrupt Enable Register
I2C_INTFL1	Interrupt Status Register 1
I2C_INTEN1	Interrupt Staus Register 1
I2C_FIFOLEN	FIFO Configuration Register
I2C_RXCTRL0	Receive Control Register 0
I2C_RXCTRL1	Receive Control Register 1
I2C_TXCTRL0	Transmit Control Register 0
I2C_TXCTRL1	Transmit Control Register 1
I2C_FIFO	Data Register
I2C_MSTCTRL	Master Control Register
I2C_CLKLO	Clock Low Register
I2C_CLKHI	Clock high Register
I2C_HSCLK	Clock high Register
I2C_TIMEOUT	Timeout Register
I2C_DMA	DMA Register
I2C_SLAVE_MULTI	Slave Address Register
►Inter-Integrated Sound (I2S)
►I2S_Registers	Registers, Bit Masks and Bit Positions for the I2S Peripheral Module
Register Offsets	I2S Peripheral Register Offsets from the I2S Base Peripheral Address
I2S_CTRL0CH0	Global mode channel
I2S_CTRL1CH0	Local channel Setup
I2S_DMACH0	DMA Control
I2S_FIFOCH0	I2S Fifo
I2S_INTFL	ISR Status
I2S_INTEN	Interrupt Enable
I2S_EXTSETUP	Ext Control
►ICC
►ICC_Registers	Registers, Bit Masks and Bit Positions for the ICC Peripheral Module
Register Offsets	ICC Peripheral Register Offsets from the ICC Base Peripheral Address
ICC_INFO	Cache ID Register
ICC_SZ	Memory Configuration Register
ICC_CTRL	Cache Control and Status Register
ICC_INVALIDATE	Invalidate All Registers
►Information Block (OTP) read interface	Read access for information block
Information Block defines	Registers, Bit Masks and Bit Positions for the Infoblock
►Low Power (LP)
►PWRSEQ_Registers	Registers, Bit Masks and Bit Positions for the PWRSEQ Peripheral Module
Register Offsets	PWRSEQ Peripheral Register Offsets from the PWRSEQ Base Peripheral Address
PWRSEQ_LPCN	Low Power Control Register
PWRSEQ_LPWKST0	Low Power I/O Wakeup Status Register 0. This register indicates the low power wakeup status for GPIO0
PWRSEQ_LPWKEN0	Low Power I/O Wakeup Enable Register 0. This register enables low power wakeup functionality for GPIO0
PWRSEQ_LPPWST	Low Power Peripheral Wakeup Status Register
PWRSEQ_LPPWEN	Low Power Peripheral Wakeup Enable Register
PWRSEQ_VBTLEPD	Low-Power VBTLE Power Down Register
Assertion Checks for Debugging	Assertion checks for debugging
Delay Utility Functions	Asynchronous delay routines based on the SysTick Timer
Error Codes	A list of common error codes used by the API
Exclusive Access Locks	Lock functions to obtain and release a variable for exclusive access. These functions are marked interrupt safe if they are interrupt safe
System Configuration (MXC_SYS)
►1-Wire Master (OWM)
►OWM_Registers	Registers, Bit Masks and Bit Positions for the OWM Peripheral Module
Register Offsets	OWM Peripheral Register Offsets from the OWM Base Peripheral Address
OWM_CFG	1-Wire Master Configuration
OWM_CLK_DIV_1US	1-Wire Master Clock Divisor
OWM_CTRL_STAT	1-Wire Master Control/Status
OWM_DATA	1-Wire Master Data Buffer
OWM_INTFL	1-Wire Master Interrupt Flags
OWM_INTEN	1-Wire Master Interrupt Enables
Pulse Train Engine	This is the high level API for the pulse train engine
►Real Time Clock (RTC)
►RTC_Registers	Registers, Bit Masks and Bit Positions for the RTC Peripheral Module
Register Offsets	RTC Peripheral Register Offsets from the RTC Base Peripheral Address
RTC_SEC	RTC Second Counter. This register contains the 32-bit second counter
RTC_SSEC	RTC Sub-second Counter. This counter increments at 256Hz. RTC_SEC is incremented when this register rolls over from 0xFF to 0x00
RTC_TODA	Time-of-day Alarm
RTC_SSECA	RTC sub-second alarm. This register contains the reload value for the sub- second alarm
RTC_CTRL	RTC Control Register
RTC_TRIM	RTC Trim Register
RTC_OSCCTRL	RTC Oscillator Control Register
►Semaphore (SEMA)
►SEMA_Registers	Registers, Bit Masks and Bit Positions for the SEMA Peripheral Module
Register Offsets	SEMA Peripheral Register Offsets from the SEMA Base Peripheral Address
SEMA_SEMAPHORES	Read to test and set, returns prior value. Write 0 to clear semaphore
SEMA_IRQ0	Semaphore IRQ0 register
SEMA_MAIL0	Semaphore Mailbox 0 register
SEMA_IRQ1	Semaphore IRQ1 register
SEMA_MAIL1	Semaphore Mailbox 1 register
SEMA_STATUS	Semaphore status bits. 0 indicates the semaphore is free, 1 indicates taken
►SIMO
►SIMO_Registers	Registers, Bit Masks and Bit Positions for the SIMO Peripheral Module
Register Offsets	SIMO Peripheral Register Offsets from the SIMO Base Peripheral Address
SIMO_VREGO_A	Buck Voltage Regulator A Control Register
SIMO_VREGO_B	Buck Voltage Regulator B Control Register
SIMO_VREGO_C	Buck Voltage Regulator C Control Register
SIMO_VREGO_D	Buck Voltage Regulator D Control Register
SIMO_IPKA	High Side FET Peak Current VREGO_A/VREGO_B Register
SIMO_IPKB	High Side FET Peak Current VREGO_C/VREGO_D Register
SIMO_MAXTON	Maximum High Side FET Time On Register
SIMO_ILOAD_A	Buck Cycle Count VREGO_A Register
SIMO_ILOAD_B	Buck Cycle Count VREGO_B Register
SIMO_ILOAD_C	Buck Cycle Count VREGO_C Register
SIMO_ILOAD_D	Buck Cycle Count VREGO_D Register
SIMO_BUCK_ALERT_THR_A	Buck Cycle Count Alert VERGO_A Register
SIMO_BUCK_ALERT_THR_B	Buck Cycle Count Alert VERGO_B Register
SIMO_BUCK_ALERT_THR_C	Buck Cycle Count Alert VERGO_C Register
SIMO_BUCK_ALERT_THR_D	Buck Cycle Count Alert VERGO_D Register
SIMO_BUCK_OUT_READY	Buck Regulator Output Ready Register
SIMO_ZERO_CROSS_CAL_A	Zero Cross Calibration VERGO_A Register
SIMO_ZERO_CROSS_CAL_B	Zero Cross Calibration VERGO_B Register
SIMO_ZERO_CROSS_CAL_C	Zero Cross Calibration VERGO_C Register
SIMO_ZERO_CROSS_CAL_D	Zero Cross Calibration VERGO_D Register
►SPI
►SPI_Registers	Registers, Bit Masks and Bit Positions for the SPI Peripheral Module
Register Offsets	SPI Peripheral Register Offsets from the SPI Base Peripheral Address
SPI_FIFO32	Register for reading and writing the FIFO
SPI_FIFO16	Register for reading and writing the FIFO
SPI_FIFO8	Register for reading and writing the FIFO
SPI_CTRL0	Register for controlling SPI peripheral
SPI_CTRL1	Register for controlling SPI peripheral
SPI_CTRL2	Register for controlling SPI peripheral
SPI_SSTIME	Register for controlling SPI peripheral/Slave Select Timing
SPI_CLKCTRL	Register for controlling SPI clock rate
SPI_DMA	Register for controlling DMA
SPI_INTFL	Register for reading and clearing interrupt flags. All bits are write 1 to clear
SPI_INTEN	Register for enabling interrupts
SPI_WKFL	Register for wake up flags. All bits in this register are write 1 to clear
SPI_WKEN	Register for wake up enable
SPI_STAT	SPI Status register
►Timer (TMR)
►TMR_Registers	Registers, Bit Masks and Bit Positions for the TMR Peripheral Module
Register Offsets	TMR Peripheral Register Offsets from the TMR Base Peripheral Address
TMR_CNT	Timer Counter Register
TMR_CMP	Timer Compare Register
TMR_PWM	Timer PWM Register
TMR_INTFL	Timer Interrupt Status Register
TMR_CTRL0	Timer Control Register
TMR_NOLCMP	Timer Non-Overlapping Compare Register
TMR_CTRL1	Timer Configuration Register
TMR_WKFL	Timer Wakeup Status Register
►TRNG
►TRNG_Registers	Registers, Bit Masks and Bit Positions for the TRNG Peripheral Module
Register Offsets	TRNG Peripheral Register Offsets from the TRNG Base Peripheral Address
TRNG_CTRL	TRNG Control Register
TRNG_STATUS	Data. The content of this register is valid only when RNG_IS = 1. When TRNG is disabled, read returns 0x0000 0000
TRNG_DATA	Data. The content of this register is valid only when RNG_IS = 1. When TRNG is disabled, read returns 0x0000 0000
►UART
►UART_Registers	Registers, Bit Masks and Bit Positions for the UART Peripheral Module
Register Offsets	UART Peripheral Register Offsets from the UART Base Peripheral Address
UART_CTRL	Control register
UART_STATUS	Status register
UART_INT_EN	Interrupt Enable control register
UART_INT_FL	Interrupt status flags Control register
UART_CLKDIV	Clock Divider register
UART_OSR	Over Sampling Rate register
UART_TXPEEK	TX FIFO Output Peek register
UART_PNR	Pin register
UART_FIFO	FIFO Read/Write register
UART_DMA	DMA Configuration register
UART_WKEN	Wake up enable Control register
UART_WKFL	Wake up Flags register
►WDT
►WDT_Registers	Registers, Bit Masks and Bit Positions for the WDT Peripheral Module
Register Offsets	WDT Peripheral Register Offsets from the WDT Base Peripheral Address
WDT_CTRL	Watchdog Timer Control Register
WDT_RST	Windowed Watchdog Timer Reset Register
WDT_CLKSEL	Windowed Watchdog Timer Clock Select Register
WDT_CNT	Windowed Watchdog Timer Count Register
►Wakeup Timer (WUT)
►WUT_Registers	Registers, Bit Masks and Bit Positions for the WUT Peripheral Module
Register Offsets	WUT Peripheral Register Offsets from the WUT Base Peripheral Address
WUT_CNT	Count. This register stores the current timer count
WUT_CMP	Compare. This register stores the compare value, which is used to set the maximum count value to initiate a reload of the timer to 0x0001
WUT_INTR	Clear Interrupt. Writing a value (0 or 1) to a bit in this register clears the associated interrupt
WUT_CTRL	Timer Control Register
WUT_NOLCMP	Timer Non-Overlapping Compare Register
WUT_PRESET	Preset register
WUT_RELOAD	Reload register
WUT_SNAPSHOT	Snapshot register
►AFE_ADC_ONE_Registers	Registers, Bit Masks and Bit Positions for the AFE_ADC_ONE Peripheral Module
Register Offsets	AFE_ADC_ONE Peripheral Register Offsets from the AFE_ADC_ONE Base Peripheral Address
AFE_ADC_ONE_PD	Power down
AFE_ADC_ONE_CONV_START	Initiate conversions
AFE_ADC_ONE_SEQ_START	Execute a sequence at written address (0x3A to 0x6E)
AFE_ADC_ONE_CAL_START	Execute selected calibration
AFE_ADC_ONE_GP0_CTRL	Control behavior of GPIO0
AFE_ADC_ONE_GP1_CTRL	Control behavior of GPIO1
AFE_ADC_ONE_GP_CONV	Select conversion to perform when initiated by GPIO
AFE_ADC_ONE_GP_SEQ_ADDR	Select target sequencer address initiated by GPIO
AFE_ADC_ONE_FILTER	Select conversion data rate and filter behavior
AFE_ADC_ONE_CTRL	Select clock source, data format, ref inputs and ref buffers
AFE_ADC_ONE_SOURCE	Configures excitation current, burnout current, and bias voltage sources
AFE_ADC_ONE_MUX_CTRL0	Selects analog inputs for AINP and AINN
AFE_ADC_ONE_MUX_CTRL1	Selects excitation current sources and which input they are connected to
AFE_ADC_ONE_MUX_CTRL2	Connection of VBIAS source to input mux
AFE_ADC_ONE_PGA	Signal path control of input buffers and PGA
AFE_ADC_ONE_WAIT_EXT	Extends count range of WAIT command
AFE_ADC_ONE_PART_ID	Silicon Revision ID
AFE_ADC_ONE_SYSC_SEL	System Calibration Selection
AFE_ADC_ONE_SYS_OFF_A	System offset A calibration value to subtract from conversion results
AFE_ADC_ONE_SYS_OFF_B	System offset B calibration value to subtract from conversion results
AFE_ADC_ONE_SYS_GAIN_A	System gain calibration A value to scale offset corrected conversion results
AFE_ADC_ONE_SYS_GAIN_B	System gain calibration B value to scale offset corrected conversion results
AFE_ADC_ONE_SELF_OFF	Self-calibration offset value to subtract from conversion results
AFE_ADC_ONE_SELF_GAIN_1	Self-calibration gain value to scale offset corrected conversion results for gain 1
AFE_ADC_ONE_SELF_GAIN_2	Self-calibration gain value to scale offset corrected conversion results for gain 2
AFE_ADC_ONE_SELF_GAIN_4	Self-calibration gain value to scale offset corrected conversion results for gain 4
AFE_ADC_ONE_SELF_GAIN_8	Self-calibration gain value to scale offset corrected conversion results for gain 8
AFE_ADC_ONE_SELF_GAIN_16	Self-calibration gain value to scale offset corrected conversion results for gain 16
AFE_ADC_ONE_SELF_GAIN_32	Self-calibration gain value to scale offset corrected conversion results for gain 32
AFE_ADC_ONE_SELF_GAIN_64	Self-calibration gain value to scale offset corrected conversion results for gain 64
AFE_ADC_ONE_SELF_GAIN_128	Self-calibration gain value to scale offset corrected conversion results for gain 128
AFE_ADC_ONE_LTHRESH0	Lower comparison threshold for DATA registers
AFE_ADC_ONE_LTHRESH1	Lower comparison threshold for DATA registers
AFE_ADC_ONE_LTHRESH2	Lower comparison threshold for DATA registers
AFE_ADC_ONE_LTHRESH3	Lower comparison threshold for DATA registers
AFE_ADC_ONE_LTHRESH4	Lower comparison threshold for DATA registers
AFE_ADC_ONE_LTHRESH5	Lower comparison threshold for DATA registers
AFE_ADC_ONE_LTHRESH6	Lower comparison threshold for DATA registers
AFE_ADC_ONE_LTHRESH7	Lower comparison threshold for DATA registers
AFE_ADC_ONE_UTHRESH0	Upper comparison threshold for DATA registers
AFE_ADC_ONE_UTHRESH1	Upper comparison threshold for DATA registers
AFE_ADC_ONE_UTHRESH2	Upper comparison threshold for DATA registers
AFE_ADC_ONE_UTHRESH3	Upper comparison threshold for DATA registers
AFE_ADC_ONE_UTHRESH4	Upper comparison threshold for DATA registers
AFE_ADC_ONE_UTHRESH5	Upper comparison threshold for DATA registers
AFE_ADC_ONE_UTHRESH6	Upper comparison threshold for DATA registers
AFE_ADC_ONE_UTHRESH7	Upper comparison threshold for DATA registers
AFE_ADC_ONE_DATA0	ADC conversion result storage
AFE_ADC_ONE_DATA1	ADC conversion result storage
AFE_ADC_ONE_DATA2	ADC conversion result storage
AFE_ADC_ONE_DATA3	ADC conversion result storage
AFE_ADC_ONE_DATA4	ADC conversion result storage
AFE_ADC_ONE_DATA5	ADC conversion result storage
AFE_ADC_ONE_DATA6	ADC conversion result storage
AFE_ADC_ONE_DATA7	ADC conversion result storage
AFE_ADC_ONE_STATUS	Device Status, INTB source etc
AFE_ADC_ONE_STATUS_IE	Device Status, INTB source etc. Enable Register
AFE_ADC_ONE_UC_0	Sequencer Register
AFE_ADC_ONE_UC_1	Sequencer Register
AFE_ADC_ONE_UC_2	Sequencer Register
AFE_ADC_ONE_UC_3	Sequencer Register
AFE_ADC_ONE_UC_4	Sequencer Register
AFE_ADC_ONE_UC_5	Sequencer Register
AFE_ADC_ONE_UC_6	Sequencer Register
AFE_ADC_ONE_UC_7	Sequencer Register
AFE_ADC_ONE_UC_8	Sequencer Register
AFE_ADC_ONE_UC_9	Sequencer Register
AFE_ADC_ONE_UC_10	Sequencer Register
AFE_ADC_ONE_UC_11	Sequencer Register
AFE_ADC_ONE_UC_12	Sequencer Register
AFE_ADC_ONE_UC_13	Sequencer Register
AFE_ADC_ONE_UC_14	Sequencer Register
AFE_ADC_ONE_UC_15	Sequencer Register
AFE_ADC_ONE_UC_16	Sequencer Register
AFE_ADC_ONE_UC_17	Sequencer Register
AFE_ADC_ONE_UC_18	Sequencer Register
AFE_ADC_ONE_UC_19	Sequencer Register
AFE_ADC_ONE_UC_20	Sequencer Register
AFE_ADC_ONE_UC_21	Sequencer Register
AFE_ADC_ONE_UC_22	Sequencer Register
AFE_ADC_ONE_UC_23	Sequencer Register
AFE_ADC_ONE_UC_24	Sequencer Register
AFE_ADC_ONE_UC_25	Sequencer Register
AFE_ADC_ONE_UC_26	Sequencer Register
AFE_ADC_ONE_UC_27	Sequencer Register
AFE_ADC_ONE_UC_28	Sequencer Register
AFE_ADC_ONE_UC_29	Sequencer Register
AFE_ADC_ONE_UC_30	Sequencer Register
AFE_ADC_ONE_UC_31	Sequencer Register
AFE_ADC_ONE_UC_32	Sequencer Register
AFE_ADC_ONE_UC_33	Sequencer Register
AFE_ADC_ONE_UC_34	Sequencer Register
AFE_ADC_ONE_UC_35	Sequencer Register
AFE_ADC_ONE_UC_36	Sequencer Register
AFE_ADC_ONE_UC_37	Sequencer Register
AFE_ADC_ONE_UC_38	Sequencer Register
AFE_ADC_ONE_UC_39	Sequencer Register
AFE_ADC_ONE_UC_40	Sequencer Register
AFE_ADC_ONE_UC_41	Sequencer Register
AFE_ADC_ONE_UC_42	Sequencer Register
AFE_ADC_ONE_UC_43	Sequencer Register
AFE_ADC_ONE_UC_44	Sequencer Register
AFE_ADC_ONE_UC_45	Sequencer Register
AFE_ADC_ONE_UC_46	Sequencer Register
AFE_ADC_ONE_UC_47	Sequencer Register
AFE_ADC_ONE_UC_48	Sequencer Register
AFE_ADC_ONE_UC_49	Sequencer Register
AFE_ADC_ONE_UC_50	Sequencer Register
AFE_ADC_ONE_UC_51	Sequencer Register
AFE_ADC_ONE_UC_52	Sequencer Register
AFE_ADC_ONE_UCADDR	Address of currently executing sequence command
AFE_ADC_ONE_FT_PWORD	FT Password
AFE_ADC_ONE_ADC_TRIM0	Various ADC Analog Trims
AFE_ADC_ONE_ADC_TRIM1	Various ADC Analog Trims
AFE_ADC_ONE_ANA_TRIM	Various Analog Trims
AFE_ADC_ONE_SYS_CTRL	System Calibration Selection
►AFE_ADC_ZERO_Registers	Registers, Bit Masks and Bit Positions for the AFE_ADC_ZERO Peripheral Module
Register Offsets	AFE_ADC_ZERO Peripheral Register Offsets from the AFE_ADC_ZERO Base Peripheral Address
AFE_ADC_ZERO_PD	Power down
AFE_ADC_ZERO_CONV_START	Initiate conversions
AFE_ADC_ZERO_SEQ_START	Execute a sequence at written address (0x3A to 0x6E)
AFE_ADC_ZERO_CAL_START	Execute selected calibration
AFE_ADC_ZERO_GP0_CTRL	Control behavior of GPIO0
AFE_ADC_ZERO_GP1_CTRL	Control behavior of GPIO1
AFE_ADC_ZERO_GP_CONV	Select conversion to perform when initiated by GPIO
AFE_ADC_ZERO_GP_SEQ_ADDR	Select target sequencer address initiated by GPIO
AFE_ADC_ZERO_FILTER	Select conversion data rate and filter behavior
AFE_ADC_ZERO_CTRL	Select clock source, data format, ref inputs and ref buffers
AFE_ADC_ZERO_SOURCE	Configures excitation current, burnout current, and bias voltage sources
AFE_ADC_ZERO_MUX_CTRL0	Selects analog inputs for AINP and AINN
AFE_ADC_ZERO_MUX_CTRL1	Selects excitation current sources and which input they are connected to
AFE_ADC_ZERO_MUX_CTRL2	Connection of VBIAS source to input mux
AFE_ADC_ZERO_PGA	Signal path control of input buffers and PGA
AFE_ADC_ZERO_WAIT_EXT	Extends count range of WAIT command
AFE_ADC_ZERO_PART_ID	Silicon Revision ID
AFE_ADC_ZERO_SYSC_SEL	System Calibration Selection
AFE_ADC_ZERO_SYS_OFF_A	System offset A calibration value to subtract from conversion results
AFE_ADC_ZERO_SYS_OFF_B	System offset B calibration value to subtract from conversion results
AFE_ADC_ZERO_SYS_GAIN_A	System gain calibration A value to scale offset corrected conversion results
AFE_ADC_ZERO_SYS_GAIN_B	System gain calibration B value to scale offset corrected conversion results
AFE_ADC_ZERO_SELF_OFF	Self-calibration offset value to subtract from conversion results
AFE_ADC_ZERO_SELF_GAIN_1	Self-calibration gain value to scale offset corrected conversion results for gain 1
AFE_ADC_ZERO_SELF_GAIN_2	Self-calibration gain value to scale offset corrected conversion results for gain 2
AFE_ADC_ZERO_SELF_GAIN_4	Self-calibration gain value to scale offset corrected conversion results for gain 4
AFE_ADC_ZERO_SELF_GAIN_8	Self-calibration gain value to scale offset corrected conversion results for gain 8
AFE_ADC_ZERO_SELF_GAIN_16	Self-calibration gain value to scale offset corrected conversion results for gain 16
AFE_ADC_ZERO_SELF_GAIN_32	Self-calibration gain value to scale offset corrected conversion results for gain 32
AFE_ADC_ZERO_SELF_GAIN_64	Self-calibration gain value to scale offset corrected conversion results for gain 64
AFE_ADC_ZERO_SELF_GAIN_128	Self-calibration gain value to scale offset corrected conversion results for gain 128
AFE_ADC_ZERO_LTHRESH0	Lower comparison threshold for DATA registers
AFE_ADC_ZERO_LTHRESH1	Lower comparison threshold for DATA registers
AFE_ADC_ZERO_LTHRESH2	Lower comparison threshold for DATA registers
AFE_ADC_ZERO_LTHRESH3	Lower comparison threshold for DATA registers
AFE_ADC_ZERO_LTHRESH4	Lower comparison threshold for DATA registers
AFE_ADC_ZERO_LTHRESH5	Lower comparison threshold for DATA registers
AFE_ADC_ZERO_LTHRESH6	Lower comparison threshold for DATA registers
AFE_ADC_ZERO_LTHRESH7	Lower comparison threshold for DATA registers
AFE_ADC_ZERO_UTHRESH0	Upper comparison threshold for DATA registers
AFE_ADC_ZERO_UTHRESH1	Upper comparison threshold for DATA registers
AFE_ADC_ZERO_UTHRESH2	Upper comparison threshold for DATA registers
AFE_ADC_ZERO_UTHRESH3	Upper comparison threshold for DATA registers
AFE_ADC_ZERO_UTHRESH4	Upper comparison threshold for DATA registers
AFE_ADC_ZERO_UTHRESH5	Upper comparison threshold for DATA registers
AFE_ADC_ZERO_UTHRESH6	Upper comparison threshold for DATA registers
AFE_ADC_ZERO_UTHRESH7	Upper comparison threshold for DATA registers
AFE_ADC_ZERO_DATA0	ADC conversion result storage
AFE_ADC_ZERO_DATA1	ADC conversion result storage
AFE_ADC_ZERO_DATA2	ADC conversion result storage
AFE_ADC_ZERO_DATA3	ADC conversion result storage
AFE_ADC_ZERO_DATA4	ADC conversion result storage
AFE_ADC_ZERO_DATA5	ADC conversion result storage
AFE_ADC_ZERO_DATA6	ADC conversion result storage
AFE_ADC_ZERO_DATA7	ADC conversion result storage
AFE_ADC_ZERO_STATUS	Device Status, INTB source etc
AFE_ADC_ZERO_STATUS_IE	Device Status, INTB source etc. Enable Register
AFE_ADC_ZERO_UC_0	Sequencer Register
AFE_ADC_ZERO_UC_1	Sequencer Register
AFE_ADC_ZERO_UC_2	Sequencer Register
AFE_ADC_ZERO_UC_3	Sequencer Register
AFE_ADC_ZERO_UC_4	Sequencer Register
AFE_ADC_ZERO_UC_5	Sequencer Register
AFE_ADC_ZERO_UC_6	Sequencer Register
AFE_ADC_ZERO_UC_7	Sequencer Register
AFE_ADC_ZERO_UC_8	Sequencer Register
AFE_ADC_ZERO_UC_9	Sequencer Register
AFE_ADC_ZERO_UC_10	Sequencer Register
AFE_ADC_ZERO_UC_11	Sequencer Register
AFE_ADC_ZERO_UC_12	Sequencer Register
AFE_ADC_ZERO_UC_13	Sequencer Register
AFE_ADC_ZERO_UC_14	Sequencer Register
AFE_ADC_ZERO_UC_15	Sequencer Register
AFE_ADC_ZERO_UC_16	Sequencer Register
AFE_ADC_ZERO_UC_17	Sequencer Register
AFE_ADC_ZERO_UC_18	Sequencer Register
AFE_ADC_ZERO_UC_19	Sequencer Register
AFE_ADC_ZERO_UC_20	Sequencer Register
AFE_ADC_ZERO_UC_21	Sequencer Register
AFE_ADC_ZERO_UC_22	Sequencer Register
AFE_ADC_ZERO_UC_23	Sequencer Register
AFE_ADC_ZERO_UC_24	Sequencer Register
AFE_ADC_ZERO_UC_25	Sequencer Register
AFE_ADC_ZERO_UC_26	Sequencer Register
AFE_ADC_ZERO_UC_27	Sequencer Register
AFE_ADC_ZERO_UC_28	Sequencer Register
AFE_ADC_ZERO_UC_29	Sequencer Register
AFE_ADC_ZERO_UC_30	Sequencer Register
AFE_ADC_ZERO_UC_31	Sequencer Register
AFE_ADC_ZERO_UC_32	Sequencer Register
AFE_ADC_ZERO_UC_33	Sequencer Register
AFE_ADC_ZERO_UC_34	Sequencer Register
AFE_ADC_ZERO_UC_35	Sequencer Register
AFE_ADC_ZERO_UC_36	Sequencer Register
AFE_ADC_ZERO_UC_37	Sequencer Register
AFE_ADC_ZERO_UC_38	Sequencer Register
AFE_ADC_ZERO_UC_39	Sequencer Register
AFE_ADC_ZERO_UC_40	Sequencer Register
AFE_ADC_ZERO_UC_41	Sequencer Register
AFE_ADC_ZERO_UC_42	Sequencer Register
AFE_ADC_ZERO_UC_43	Sequencer Register
AFE_ADC_ZERO_UC_44	Sequencer Register
AFE_ADC_ZERO_UC_45	Sequencer Register
AFE_ADC_ZERO_UC_46	Sequencer Register
AFE_ADC_ZERO_UC_47	Sequencer Register
AFE_ADC_ZERO_UC_48	Sequencer Register
AFE_ADC_ZERO_UC_49	Sequencer Register
AFE_ADC_ZERO_UC_50	Sequencer Register
AFE_ADC_ZERO_UC_51	Sequencer Register
AFE_ADC_ZERO_UC_52	Sequencer Register
AFE_ADC_ZERO_UCADDR	Address of currently executing sequence command
AFE_ADC_ZERO_FT_PWORD	FT Password
AFE_ADC_ZERO_ADC_TRIM0	Various ADC Analog Trims
AFE_ADC_ZERO_ADC_TRIM1	Various ADC Analog Trims
AFE_ADC_ZERO_ANA_TRIM	Various Analog Trims
AFE_ADC_ZERO_SYS_CTRL	System Calibration Selection
►AFE_DAC_Registers	Registers, Bit Masks and Bit Positions for the AFE_DAC Peripheral Module
Register Offsets	AFE_DAC Peripheral Register Offsets from the AFE_DAC Base Peripheral Address
AFE_DAC_CTRL	Control Register
AFE_DAC_RATE	Rate/Sample Control
AFE_DAC_INT	Interrupt Flags and Enable/Disable
AFE_DAC_VREF_CTRL	DAC VREF Control
AFE_DAC_FIFO	DAC FIFO
AFE_DAC_VREF_TRIM	Control behavior of GPIO1
►AFE_HART_Registers	Registers, Bit Masks and Bit Positions for the AFE_HART Peripheral Module
Register Offsets	AFE_HART Peripheral Register Offsets from the AFE_HART Base Peripheral Address
AFE_HART_CTRL	HART Control
AFE_HART_RX_TX_CTL	Control HART Transmit and Receive Functions
AFE_HART_RX_CTL_EXT1	Receive Control Extension Register 1
AFE_HART_RX_CTL_EXT2	Receive Control Extension Register 2
AFE_HART_RX_DB_THRSHLD	Receive Bit-Detect/Demodulation Threshold
AFE_HART_RX_CRD_UP_THRSHLD	Receive Carrier Detect Up Threshold Register
AFE_HART_RX_CRD_DN_THRSHLD	Receive Carrier Detect Down Threshold Register
AFE_HART_RX_CRD_DOUT_THRSHLD	Receive Carrier Detect DOUT Threshold
AFE_HART_TX_MARKSPACE_CNT	Transmit Mark-Space Count Values
AFE_HART_TRIM	HART Trim Register
AFE_HART_TM	Testmode
►DVS_Registers	Registers, Bit Masks and Bit Positions for the DVS Peripheral Module
Register Offsets	DVS Peripheral Register Offsets from the DVS Base Peripheral Address
DVS_CTL	Control Register
DVS_STAT	Status Fields
DVS_DIRECT	Direct control of target voltage
DVS_MON	Monitor Delay
DVS_ADJ_UP	Up Delay Register
DVS_ADJ_DWN	Down Delay Register
DVS_THRES_CMP	Up Delay Register
DVS_TAP_SEL	DVS Tap Select Register
►FCR_Registers	Registers, Bit Masks and Bit Positions for the FCR Peripheral Module
Register Offsets	FCR Peripheral Register Offsets from the FCR Base Peripheral Address
FCR_FCTRL0	Function Control 0
FCR_AUTOCAL0	Automatic Calibration 0
FCR_AUTOCAL1	Automatic Calibration 1
FCR_AUTOCAL2	Automatic Calibration 2
FCR_URVCTRL	RISC-V Control Register
FCR_ERFOKS	ERFO Kick Start Register
►GCFR_Registers	Registers, Bit Masks and Bit Positions for the GCFR Peripheral Module
Register Offsets	GCFR Peripheral Register Offsets from the GCFR Base Peripheral Address
GCFR_REG0	Register 0
GCFR_REG1	Register 1
►GCR_Registers	Registers, Bit Masks and Bit Positions for the GCR Peripheral Module
Register Offsets	GCR Peripheral Register Offsets from the GCR Base Peripheral Address
GCR_SYSCTRL	System Control
GCR_RST0	Reset
GCR_CLKCTRL	Clock Control
GCR_PM	Power Management
GCR_PCLKDIV	Peripheral Clock Divider
GCR_PCLKDIS0	Peripheral Clock Disable
GCR_MEMCTRL	Memory Clock Control Register
GCR_MEMZ	Memory Zeroize Control
GCR_SYSST	System Status Register
GCR_RST1	Reset 1
GCR_PCLKDIS1	Peripheral Clock Disable
GCR_EVENTEN	Event Enable Register
GCR_REVISION	Revision Register
GCR_SYSIE	System Status Interrupt Enable Register
GCR_ECCERR	ECC Error Register
GCR_ECCCED	ECC Not Double Error Detect Register
GCR_ECCIE	ECC IRQ Enable Register
GCR_ECCADDR	ECC Error Address Register
GCR_BTLELDOCTRL	BTLE LDO Control Register
GCR_BTLELDODLY	BTLE LDO Delay Register
►LPCMP_Registers	Registers, Bit Masks and Bit Positions for the LPCMP Peripheral Module
Register Offsets	LPCMP Peripheral Register Offsets from the LPCMP Base Peripheral Address
LPCMP_CTRL	Comparator Control Register
►LPGCR_Registers	Registers, Bit Masks and Bit Positions for the LPGCR Peripheral Module
Register Offsets	LPGCR Peripheral Register Offsets from the LPGCR Base Peripheral Address
LPGCR_RST	Low Power Reset Register
LPGCR_PCLKDIS	Low Power Peripheral Clock Disable Register
►MCR_Registers	Registers, Bit Masks and Bit Positions for the MCR Peripheral Module
Register Offsets	MCR Peripheral Register Offsets from the MCR Base Peripheral Address
MCR_ECCEN	ECC Enable Register
MCR_IPO_MTRIM	IPO Manual Register
MCR_OUTEN	Output Enable Register
MCR_CMP_CTRL	Comparator Control Register
MCR_CTRL	Miscellaneous Control Register
MCR_GPIO3_CTRL	GPIO3 Pin Control Register
►PT_Registers	Registers, Bit Masks and Bit Positions for the PT Peripheral Module
Register Offsets	PT Peripheral Register Offsets from the PT Base Peripheral Address
PT_RATE_LENGTH	Pulse Train Configuration
PT_LOOP	Pulse Train Loop Count
PT_RESTART	Pulse Train Auto-Restart Configuration
►PTG_Registers	Registers, Bit Masks and Bit Positions for the PTG Peripheral Module
Register Offsets	PTG Peripheral Register Offsets from the PTG Base Peripheral Address
PTG_ENABLE	Global Enable/Disable Controls for All Pulse Trains
PTG_RESYNC	Global Resync (All Pulse Trains) Control
PTG_INTFL	Pulse Train Interrupt Flags
PTG_INTEN	Pulse Train Interrupt Enable/Disable
PTG_SAFE_EN	Pulse Train Global Safe Enable
PTG_SAFE_DIS	Pulse Train Global Safe Disable
►SIR_Registers	Registers, Bit Masks and Bit Positions for the SIR Peripheral Module
Register Offsets	SIR Peripheral Register Offsets from the SIR Base Peripheral Address
SIR_SISTAT	System Initialization Status Register
SIR_ADDR	Read-only field set by the SIB block if a CRC error occurs during the read of the OTP memory. Contains the failing address in OTP memory (when CRCERR equals 1)
SIR_BTLE_LDO_TRIM	BTLE LDO Trim register
SIR_FSTAT	Funcstat register
SIR_SFSTAT	Security function status register
►TRIMSIR_Registers	Registers, Bit Masks and Bit Positions for the TRIMSIR Peripheral Module
Register Offsets	TRIMSIR Peripheral Register Offsets from the TRIMSIR Base Peripheral Address
TRIMSIR_RTC	RTC Trim System Initialization Register
TRIMSIR_SIMO	SIMO Trim System Initialization Register
TRIMSIR_IPOLO	IPO Low Trim System Initialization Register
TRIMSIR_CTRL	Control Trim System Initialization Register
TRIMSIR_INRO	RTC Trim System Initialization Register