ADRV9009 HDL reference design

The HDL reference design is an embedded system built around a processor core either ARM, NIOS-II or Microblaze. A functional block diagram of the system is shown below. The device digital interface is handled by the transceiver IP followed by the JESD204B and device specific cores. The JESD204B lanes are shared among the 4 transmit, 2 receive and 2 observation/sniffer receive data paths by the same set of transceivers within the IP. The cores are programmable through an AXI-lite interface. The delineated data is then passed on to independent DMA cores for the transmit, receive and observation/sniffer paths.

Supported boards

Supported carriers

Evaluation board

Carrier

FMC slot

ADRV9008/9

A10SoC

FMCA

S10SoC

FMCA

ZC706

FMC_HPC

ZCU102

FMC HPC1

Block design

Block diagram

The data path and clock domains are depicted in the below diagrams:

Digital Interface

The digital interface consists of 4 transmit, 2 receive and 2 observation/sniffer lanes running up to 9.8Gbps. The transceivers then interface to the cores at 128bits @245.76MHz in the transmit and 64bits @245.76MHz for the receive channels. The sniffer/observation rates depend on the mode selected. The data is sent or received based on the configuration (programmable) from separate transmit and receive chains.

DAC Interface

The DAC data may be sourced from an internal data generator (DDS or pattern) or from the external DDR via DMA. The internal DDS phase and frequency are programmable. DAC unpack IP allows transfering data from the DMA to a reduced number of channels, at a higher rate.

ADC Interface

The ADC data is sent to the DDR via DMA. The ADC pack IP allows capturing only part of the channels.

Control and SPI

The device control and monitor signals are interfaced to a GPIO module. The SPI signals are controlled by a separate AXI based SPI core.

Configuration modes

The block design supports configuration of parameters and scales.

We have listed a couple of examples at section Building the HDL project and the default modes for each project.

Note

The parameters for Rx or Tx links can be changed from the system_project.tcl file, located in hdl/projects/adrv9009/$CARRIER/system_project.tcl

LaneRate=SampleRate∗ML∗N′∗108

The following are the parameters of this project that can be configured:

  • [RX/TX/RX_OS]_JESD_M: number of converters per link

  • [RX/TX/RX_OS]_JESD_L: number of lanes per link

  • [RX/TX/RX_OS]_JESD_S: number of samples per frame

CPU/Memory interconnects addresses

The addresses are dependent on the architecture of the FPGA, having an offset added to the base address from HDL (see more at CPU/Memory interconnects addresses).

Instance

Zynq

ZynqMP

rx_adrv9009_tpl_core

0x44A0_0000

0x84A0_0000

tx_adrv9009_tpl_core

0x44A0_4000

0x84A0_4000

rx_os_adrv9009_tpl_core

0x44A0_8000

0x84A0_8000

axi_adrv9009_rx_xcvr

0x44A6_0000

0x84A6_0000

axi_adrv9009_tx_xcvr

0x44A8_0000

0x84A8_0000

axi_adrv9009_rx_os_xcvr

0x44A5_0000

0x84A5_0000

axi_adrv9009_tx_jesd

0x44A9_0000

0x84A9_0000

axi_adrv9009_rx_jesd

0x44AA_0000

0x84AA_0000

axi_adrv9009_rx_os_jesd

0x44AB_0000

0x84AB_0000

axi_adrv9009_rx_dma

0x7C40_0000

0x9C40_0000

axi_adrv9009_tx_dma

0x7C42_0000

0x9C42_0000

axi_adrv9009_rx_os_dma

0x7C44_0000

0x9C44_0000

adrv9009_data_offload

0x7c43_0000

0x9C43_0000

axi_adrv9009_rx_clkgen

0x43C1_0000

0x83C1_0000

axi_adrv9009_tx_clkgen

0x43C0_0000

0x83C0_0000

axi_adrv9009_rx_os_clkgen

0x43C2_0000

0x83C2_0000

SPI connections

SPI type

SPI manager instance

SPI subordinate

CS

PS

spi0

AD9528

0

ADRV9009

1

GPIOs

GPIO signal

Direction

HDL GPIO EMIO

Software GPIO

(from FPGA view)

Zynq MP

ad9528_reset_b

INOUT

59

137

ad9528_sysref_req

INOUT

58

136

adrv9009_tx1_enable

INOUT

57

135

adrv9009_tx2_enable

INOUT

56

134

adrv9009_rx1_enable

INOUT

55

133

adrv9009_rx2_enable

INOUT

54

132

adrv9009_test

INOUT

53

131

adrv9009_reset_b

INOUT

52

130

adrv9009_gpint

INOUT

51

129

adrv9009_gpio_{00:18}

INOUT

50:32

128:110

Interrupts

Below are the Programmable Logic interrupts used in this project.

Instance name

HDL

Linux Zynq

Actual Zynq

Linux ZynqMP

Actual ZynqMP

axi_adrv9009_rx_os_jesd

8

52

84

104

136

axi_adrv9009_tx_jesd

9

53

85

105

137

axi_adrv9009_rx_jesd

10

54

86

106

138

axi_adrv9009_rx_os_dma

11

55

87

107

139

axi_adrv9009_tx_dma

12

56

88

108

140

axi_adrv9009_rx_dma

13

57

89

109

141

Building the HDL project

The design is built upon ADI’s generic HDL reference design framework. ADI distributes the bit/elf files of these projects as part of the ADI Kuiper Linux. If you want to build the sources, ADI makes them available on the HDL repository. To get the source you must clone the HDL repository.

Then go to the project location, choose your carrier and run the make command by typing in your command prompt:

Linux/Cygwin/WSL

~$

cd hdl/projects/adrv9009/zcu102

~/hdl/projects/adrv9009/zcu102$

make

The following dropdowns contain tables with the parameters that can be used to configure this project, depending on the carrier used.

Parameter

Default value of the parameters depending on carrier

A10SoC/S10SoC/ZC706/ZCU102

RX_JESD_M

4

RX_JESD_L

2

RX_JESD_S

1

TX_JESD_M

4

TX_JESD_L

4

TX_JESD_S

1

RX_OS_JESD_M

2

RX_OS_JESD_L

2

RX_OS_JESD_S

1

A more comprehensive build guide can be found in the Build an HDL project user guide.

Other considerations

ADC - lane mapping

Due to physical constraints, Rx lanes are reordered as described in the following table.

ADC phy Lane

FPGA Rx lane / Logical Lane

0

0

1

1

ADC OBS phy Lane

FPGA Rx lane / Logical Lane

0

2

1

3

DAC - lane mapping

Due to physical constraints, Tx lanes are reordered as described in the following table.

DAC phy lane

FPGA Tx lane / Logical lane

0

3

1

2

2

0

3

1

Resources

More information

Support

Analog Devices, Inc. will provide limited online support for anyone using the reference design with ADI components via the EngineerZone FPGA reference designs forum.

For questions regarding the ADI Linux device drivers, device trees, etc. from our Linux GitHub repository, the team will offer support on the EngineerZone Linux software drivers forum.

For questions concerning the ADI No-OS drivers, from our No-OS GitHub repository, the team will offer support on the EngineerZone microcontroller No-OS drivers forum.

It should be noted, that the older the tools’ versions and release branches are, the lower the chances to receive support from ADI engineers.