Add device

Note

User guide: Scopy Overview.

Note

Tester

Test Date

Scopy version

Plugin version (N/A if not applicable)

Comments

Setup environment:

M2k.Emu:

  • Open Scopy.

  • Start the iio-emu process using “adalm2000” in the dropdown and “ip:127.0.0.1” as URI.

Test 1: Verifying the device scanning functionality.

UID: TST.ADD.SCAN_ALL

Description: This test checks that the device scan correctly detects and lists available devices when initiated.

Preconditions:

  • Scopy is installed on the system.

  • OS: ANY.

Steps:

  1. Connect an ADALM2000 device to the system by USB.

  2. Open Scopy.

  3. Click on Add device (+) button.

  4. Click on the refresh button on the right located in the Add page scan section.

  5. Wait until the refresh animation stops.

    • Expected result: In the “Context” dropdown, all available devices are listed, each item containing the device name/description and URI. The ADALM2000 device [usb] must appear in the list.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 2: Verifying the local device scanning functionality.

UID: TST.ADD.SCAN_LOCAL

Description: This test checks that the device scan correctly detects and lists available local devices when initiated.

Preconditions:

  • Scopy is installed on the system.

  • There is at least one IIO device connected to the system that has local backend.

  • OS: Linux-x86_64.

Steps:

  1. Open Scopy.

  2. Click on Add device (+) button.

  3. Check only the local checkbox located in the Add page scan section.

  4. Wait until the refresh animation stops.

    • Expected result: In the “Context” dropdown, all available local devices are listed, each item containing the device name/description and URI. If there is no available device the “No scanned devices available!” message is displayed.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 3: Verifying the ip device scanning functionality.

UID: TST.ADD.SCAN_IP

Description: This test checks that the device scan correctly detects and lists available ip devices when initiated.

Preconditions:

  • Scopy is installed on the system.

  • There is at least one IIO device connected to the system that has ip backend.

  • OS: ANY.

Steps:

  1. Open Scopy.

  2. Click on Add device (+) button.

  3. Check only the ip checkbox located in the Add page scan section.

  4. Wait until the refresh animation stops.

    • Expected result: In the “Context” dropdown, all available ip devices are listed, each item containing the device name/description and URI. If there is no available device the “No scanned devices available!” message is displayed.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 4: Verifying the usb device scanning functionality.

UID: TST.ADD.SCAN_USB

Description: This test checks that the device scan correctly detects and lists available usb devices when initiated.

Preconditions:

  • Scopy is installed on the system.

  • OS: ANY.

Steps:

  1. Connect an ADALM2000 device to the system by USB.

  2. Open Scopy.

  3. Click on Add device (+) button.

  4. Check only the usb checkbox located in the Add page scan section.

  5. Wait until the refresh animation stops.

    • Expected result: In the “Context” dropdown, all available usb devices are listed, each item containing the device name/description and URI. The ADALM2000 device must appear in the list.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 5: Verifying the serial device scanning functionality.

UID: TST.ADD.SCAN_SERIAL

Description: This test checks that the device scan correctly detects and lists available serial devices when initiated.

Preconditions:

  • Scopy is installed on the system.

  • There is at least one IIO device connected to the system that has serial backend.

  • OS: ANY.

Steps:

  1. Open Scopy.

  2. Click on Add device (+) button.

  3. Click on the refresh button on the right located in the Add page serial port section.

  4. Wait until the refresh animation stops.

    • Expected result: In the “Name” dropdown, all available serial devices are listed, each item containing the device name/description and URI. If there is no available device the “No scanned devices available!” message is displayed.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 6: Scanning with no device.

UID: TST.ADD.SCAN_EMPTY

Description: This test checks whether an appropriate message is displayed when no device is found.

Preconditions:

  • Scopy is installed on the system.

  • OS: ANY.

Steps:

  1. Run Scopy.

  2. Make sure that no devices using USB backends are connected to the system.

  3. Click on Add device (+) button.

  4. Click on usb checkbox located in the Add page scan section.

  5. Wait until the refresh animation stops.

    • Expected result: The “No scanned devices available!” message is displayed.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 7: Device validation.

UID: TST.ADD.VERIFY

Description: This test verifies that the device validation works correctly.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • iio-emu is installed on the system.

  • Use M2k.Emu setup.

  • OS: ANY.

Steps:

  1. Click on Add device (+) button.

  2. Introduce the “ip:127.0.0.1” URI.

  3. Click on Verify button.

    • Expected result: A loading animation starts and after a short time a page with device details and compatible plugins is displayed.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 8: Verify the “BACK” button from compatible plugin page.

UID: TST.ADD.PLUGINS_BACK

Description: This test checks if the BACK button works correctly.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • iio-emu is installed on the system.

  • Use M2k.Emu setup.

  • OS: ANY.

Steps:

  1. Click on Add device (+) button.

  2. Introduce the “ip:127.0.0.1” URI.

  3. Click on Verify button.

  4. Click on BACK button.

    • Expected result: The verify page is displayed.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 9: Verify the “ADD DEVICE” button from compatible plugin page (single plugin).

UID: TST.ADD.PLUGINS_ADD_SINGLE

Description: This test checks if the ADD DEVICE button works correctly. Only the main plugin of the device is used.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • iio-emu is installed on the system.

  • Use M2k.Emu setup.

  • OS: ANY.

Steps:

  1. Click on Add device (+) button.

  2. Introduce the “ip:127.0.0.1” URI.

  3. Click on Verify button.

    • Expected result: Only the M2kPlugin should be selected in the compatible plugins section.

    • Actual result:

  1. Click on ADD DEVICE button.

    • Expected result: The device is added to the device browser, the device’s info page is displayed, and the m2k tools are added to the tool menu.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 10: Verify the “ADD DEVICE” button from compatible plugin page (multiple plugins).

UID: TST.ADD.PLUGINS_ADD_MULTIPLE

Description: This test checks if the ADD DEVICE button works correctly. Multiple plugins are used.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • iio-emu is installed on the system.

  • Use M2k.Emu setup.

  • OS: ANY.

Steps:

  1. Click on Add device (+) button.

  2. Introduce the “ip:127.0.0.1” URI.

  3. Click on Verify button.

    • Expected result: Only the M2kPlugin should be selected in the compatible plugins section.

    • Actual result:

  1. Select the DebuggerPlugin.

  2. Click on ADD DEVICE button.

    • Expected result: The device is added to the device browser, the device’s info page is displayed, and all tools, including the debugger, are added to the tool menu.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 11: Verify the “ADD DEVICE” button from compatible plugin page with no plugin selected.

UID: TST.ADD.PLUGINS_EMPTY

Description: This test checks if the ADD DEVICE button works correctly.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • iio-emu is installed on the system.

  • Use M2k.Emu setup.

  • OS: ANY.

Steps:

  1. Click on Add device (+) button.

  2. Introduce the “ip:127.0.0.1” URI.

  3. Click on Verify button.

    • Expected result: Only the M2kPlugin should be selected in the compatible plugins section.

    • Actual result:

  1. Uncheck the M2kPlugin.

  2. Click on ADD DEVICE button.

    • Expected result: A NO_PLUGIN device is added in device browser and in tool menu.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL