Connection flow

Note

User guide: Scopy Overview.

Note

Tester

Test Date

Scopy version

Plugin version (N/A if not applicable)

Comments

Setup environment:

M2k.Emu:

  • Open Scopy.

  • Start the iio-emu process using “adalm2000” in the dropdown and “ip:127.0.0.1” as URI.

  • Add the device in device browser.

M2k.Usb:

  • Open Scopy.

  • Connect an ADALM2000 device to the system by USB.

  • Add the device in device browser.

Test 1: Verify the connection flow.

UID: TST.CONN.SUCC

Description: This test checks if the Connect button works correctly.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • iio-emu is installed in the system.

  • Use M2k.Emu setup.

  • OS: ANY.

Steps:

  1. Click on the device icon from device browser.

  2. Click on Connect button.

    • Expected result: The Disconnect button appears, a status bar is displayed under the icon in the device browser, and a progress bar appears in the application’s status bar. After a while, the connection is established, the status bar turns green, and the tools in the menu become accessible.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 2: Unplug the device while connecting (AUTO-SCAN).

UID: TST.CONN.UNPLUG_AUTO

Description: This test verifies Scopy’s behavior when the device is unplugged during the connection process.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • The “Regularly scan for new devices” preference is enabled in the preferences page.

  • Use M2k.Usb setup.

  • OS: ANY.

Steps:

  1. Click on the device icon from device browser.

  2. Click on Connect button.

  3. Unplug the device while connecting.

    • Expected result: The device is removed from device browser.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 3: Unplug the device while connecting (MANUAL-SCAN).

UID: TST.CONN.UNPLUG_AUTO

Description: This test verifies Scopy’s behavior when the device is unplugged during the connection process.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • The “Regularly scan for new devices” preference is disabled in the preferences page.

  • Use M2k.Usb setup.

  • OS: ANY.

Steps:

  1. Click on the device icon from device browser.

  2. Click on Connect button.

  3. Unplug the device while connecting.

    • Expected result: A warning icon appears in the top-right corner of the device in the device browser, and when hovered over, the message “The device is not available! Verify the connection!” is displayed.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 4: Unplug the device before connecting.

UID: TST.CONN.UNPLUG_BEFORE

Description: This test verifies Scopy’s behavior when the device is unplugged before the connection process.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • The “Regularly scan for new devices” preference is disabled in the preferences page.

  • Use M2k.Usb setup.

  • OS: ANY.

Steps:

  1. Click on the device icon from device browser.

  2. Unplug the device.

  3. Click on Connect button.

    • Expected result: The connection process starts but does not complete. A warning icon appears in the top-right corner.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL

Test 5: Disconnecting a device.

UID: TST.CONN.DISCONN

Description: This test checks if the Disconnect button works correctly.

Test prerequisites:
Preconditions:

  • Scopy is installed on the system.

  • iio-emu is installed in the system.

  • Use M2k.Emu setup.

  • OS: ANY.

Steps:

  1. Click on the device icon from device browser.

  2. Click on Connect button.

  3. Wait until the connection is done .

  4. Click on Disconnect button.

    • Expected result: The device is disconnected, the Connect button appears, the device remains in the device browser, and the tools in the menu are no longer accessible.

    • Actual result:

Tested OS:

Comments:

Result: PASS/FAIL