AD9084-FMCA-EBZ Virtex UltraScale+ VCU118/VCU128 Quick Start Guide
This guide provides some quick instructions on how to setup the AD9084 eval board on:
Required Hardware
AD9084-FMCA-EBZ evaluation board
2 x Micro-USB cable
Ethernet cables
Power supply for the FPGA carrier board and the AD9084-FMCA-EBZ evaluation board
Required Software
A Linux OS on a PC
Xilinx Vivado 2025.1
Xilinx Vitis 2025.1
A UART terminal (Putty/Tera Term/Minicom, etc.), Baud rate 115200 (8N1).
IIO-Oscilloscope with the AD9084 plugin
Building the HDL project
Before building the hdl project setup your computer based on the following guide: Build an HDL project
user@analog:~$
git clone https://github.com/analogdevicesinc/hdl.git
user@analog:~$
cd hdl/projects/ad9084_ebz/vcu118
user@analog:~/hdl/projects/ad9084_ebz/vcu118$
make
Building ad9084_ebz_vcu118 [/home/analog/hdl/projects/ad9084_ebz/vcu118/ad9084_ebz_vcu118_vivado.log] ... OK
Build the Linux files
Microblaze gnu toolchain from Xilinx is no longer available on gcc. Please use gnu tools from Vitis installation as below:
user@analog:~$
export PATH=/opt/Xilinx/Vitis/2025.1/gnu/microblaze/linux_toolchain/lin64_le/bin/:$PATH
user@analog:~$
export ARCH=microblaze
user@analog:~$
export CROSS_COMPILE=microblazeel-xilinx-linux-gnu-
or alternatively, source the Vivado settings64.sh as below:
user@analog:~$
source /opt/Xilinx/Vivado/2025.1/settings64.sh
user@analog:~$
export ARCH=microblaze
user@analog:~$
export CROSS_COMPILE=microblazeel-xilinx-linux-gnu-
Get Linux kernel source
user@analog:~$
git clone https://github.com/analogdevicesinc/linux.git
Cloning into 'linux'...
remote: Counting objects: 2757163, done.
remote: Compressing objects: 100% (495484/495484), done.
remote: Total 2757163 (delta 2296596), reused 2687337 (delta 2234506)
Receiving objects: 100% (2757163/2757163), 782.04 MiB | 1.39 MiB/s, done.
Resolving deltas: 100% (2296596/2296596), done.
Get the Root File-System
The root file system or rootfs contains everything (besides the Linux kernel itself) needed to support a full Linux system. It contains all the (user) applications, configurations, services, data, etc. Without the rootfs your Linux system cannot run. You can either just download the pre-build image or build it yourself. Instructions can be found here: Building with buildroot
user@analog:~$
cd linux
user@analog:~/linux$
wget https://swdownloads.analog.com/cse/microblaze/rootfs/rootfs.cpio.gz
--2022-01-18 09:52:08-- https://swdownloads.analog.com/cse/microblaze/rootfs/rootfs.cpio.gz
Resolving swdownloads.analog.com (swdownloads.analog.com)... 23.63.205.142
Connecting to swdownloads.analog.com (swdownloads.analog.com)|23.63.205.142|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 6772207 (6,5M) [application/x-gzip]
Saving to: ‘rootfs.cpio.gz’
rootfs.cpio.gz 100%[===============================================================================================================>] 6,46M 3,32MB/s in 1,9s
2022-01-18 09:52:12 (3,32 MB/s) - ‘rootfs.cpio.gz’ saved [6772207/6772207]
Important
rootfs.cpio.gz must be placed in the root of your kernel tree. (~/linux/rootfs.cpio.gz)
Configure the Kernel and build it
The following command shows the general format for the build target name:
~$
make simpleImage.<dts file name>
Note
The <dts file name> does not include the file extension “.dts”.
To see what device-trees for the different FPGA carrier and FMC module combination exist type:
~/linux$
ls -l arch/microblaze/boot/dts | grep ad9084
Building the kernel with the default device tree
Important
If you wish to use a non-default AD9084 profile, follow the steps in the AD9084 Profile Generator before proceeding in order to add the profile to the Linux build.
user@analog:~$
cd linux
user@analog:~/linux$
make adi_mb_defconfig
user@analog:~/linux$
#
user@analog:~/linux$
# configuration written to .config
user@analog:~/linux$
#
user@analog:~/linux$
make -j4 simpleImage.vcu118_ad9084
SYNC include/config/auto.conf.cmd
CC scripts/mod/empty.o
CC scripts/mod/devicetable-offsets.s
MKELF scripts/mod/elfconfig.h
HOSTCC scripts/mod/modpost.o
HOSTCC scripts/mod/sumversion.o
HOSTCC scripts/mod/file2alias.o
[ --snip-- ]
AR init/built-in.a
LD vmlinux.o
MODPOST vmlinux.symvers
MODINFO modules.builtin.modinfo
GEN modules.builtin
LD .tmp_vmlinux.kallsyms1
KSYMS .tmp_vmlinux.kallsyms1.S
AS .tmp_vmlinux.kallsyms1.S
LD .tmp_vmlinux.kallsyms2
KSYMS .tmp_vmlinux.kallsyms2.S
AS .tmp_vmlinux.kallsyms2.S
LD vmlinux
SORTTAB vmlinux
SYSMAP System.map
OBJCOPY arch/microblaze/boot/simpleImage.vcu118_ad9084
SHIPPED arch/microblaze/boot/simpleImage.vcu118_ad9084.unstrip
STRIP vmlinux arch/microblaze/boot/simpleImage.vcu118_ad9084.strip
UIMAGE arch/microblaze/boot/simpleImage.vcu118_ad9084.ub
Image Name: Linux-5.10.0-97916-g513446e488c3
Created: Tue Jan 18 12:07:35 2022
Image Type: MicroBlaze Linux Kernel Image (uncompressed)
Data Size: 18398124 Bytes = 17966.92 KiB = 17.55 MiB
Load Address: 80000000
Entry Point: 80000000
Kernel: arch/microblaze/boot/simpleImage.vcu118_ad9084 is ready (#3678)
Note
The STRIP image found under arch/microblaze/boot/ is the ELF image which can be loaded via the debugger
Testing
First we need to prepare a working directory where we will gather all the required binary files.
From the HDL build directory locate the system_top.bit and copy it to the working directory.
From the Linux build directory locate the simpleImage and copy it to the working directory.
~$
mkdir working_dir
~$
cp <hdl_repo_dir>/projects/ad9084_ebz/vcu118/ad9084_ebz_vcu118.runs/impl_1/system_top.bit working_dir
~$
cp <linux_repo_dir>/arch/microblaze/boot/simpleImage.vcu118_ad9084.strip working_dir
Next step is to program the board with xsct or similar tool
~$
xsct
~$
xsct% connect
~$
xsct% fpga -f system_top.bit
~$
xsct% after 1000
~$
xsct% target 3
~$
xsct% dow simpleImage.vcu118_ad9084.strip
~$
xsct% after 1000
~$
xsct% con
~$
xsct% disconnect
Note
Login Information
user: analog
password: analog
Xilinx Zynq MP First Stage Boot Loader
Release 2017.4 May 11 2018 - 15:08:48
NOTICE: ATF running on XCZU9EG/silicon v4/RTL5.1 at 0xfffea000, with PMU firmware
NOTICE: BL31: Secure code at 0x0
NOTICE: BL31: Non secure code at 0x8000000
NOTICE: BL31: v1.3(release):47af34b
NOTICE: BL31: Built : 15:08:13, May 11 2018
PMUFW: v0.3
U-Boot 2017.01 (May 02 2018 - 15:53:29 +0200) Xilinx ZynqMP ZCU102 rev1.0
I2C: ready
DRAM: 4 GiB
EL Level: EL2
Chip ID: xczu9eg
MMC: sdhci@ff170000: 0 (SD)
reading uboot.env
In: serial@ff000000
Out: serial@ff000000
Err: serial@ff000000
Net: ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id
eth0: ethernet@ff0e0000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Device: sdhci@ff170000
Manufacturer ID: 3
OEM: 5344
Name: SL16G
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.8 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
reading uEnv.txt
380 bytes read in 8 ms (45.9 KiB/s)
Loaded environment from uEnv.txt
Importing environment from SD ...
Running uenvcmd ...
Copying Linux from SD to RAM...
** No boot file defined **
reading system.dtb
59378 bytes read in 40 ms (1.4 MiB/s)
reading Image
15008256 bytes read in 1024 ms (14 MiB/s)
## Flattened Device Tree blob at 04000000
Booting using the fdt blob at 0x4000000
Loading Device Tree to 000000000ffee000, end 000000000ffff7f1 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.0-g6834429-dirty (michael@mhenneri-D06) (gcc version 6.2.1 20161114 (Linaro GCC Snapshot 6.2-2016.11) ) #604 SMP Mon May 14 10:19:03 CEST 2018
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 256 MiB at 0x0000000070000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff57000 s47384 r8192 d30440 u86016
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1034240
[ 0.000000] Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext4 rootwait root=/dev/mmcblk0p2 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] software IO TLB [mem 0x6bfff000-0x6ffff000] (64MB) mapped at [ffffffc06bfff000-ffffffc06fffefff]
[ 0.000000] Memory: 3786888K/4194304K available (9468K kernel code, 640K rwdata, 3968K rodata, 512K init, 388K bss, 145272K reserved, 262144K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff80089c0000 ( 9472 KB)
[ 0.000000] .rodata : 0xffffff80089c0000 - 0xffffff8008db0000 ( 4032 KB)
[ 0.000000] .init : 0xffffff8008db0000 - 0xffffff8008e30000 ( 512 KB)
[ 0.000000] .data : 0xffffff8008e30000 - 0xffffff8008ed0200 ( 641 KB)
[ 0.000000] .bss : 0xffffff8008ed0200 - 0xffffff8008f31534 ( 389 KB)
[ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf1dc00000 ( 476 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc880000000 ( 34816 MB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 99.99MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x170f8dc196, max_idle_ns: 440795203664 ns
[ 0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511099ns
[ 0.000322] Console: colour dummy device 80x25
[ 0.000338] Calibrating delay loop (skipped), value calculated using timer frequency.. 199.98 BogoMIPS (lpj=399960)
[ 0.000346] pid_max: default: 32768 minimum: 301
[ 0.000441] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.000447] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.000935] ASID allocator initialised with 65536 entries
[ 0.001448] zynqmp_plat_init Power management API v0.3
[ 0.001520] EFI services will not be available.
[ 0.001824] Detected VIPT I-cache on CPU1
[ 0.001850] CPU1: Booted secondary processor [410fd034]
[ 0.002097] Detected VIPT I-cache on CPU2
[ 0.002115] CPU2: Booted secondary processor [410fd034]
[ 0.002357] Detected VIPT I-cache on CPU3
[ 0.002374] CPU3: Booted secondary processor [410fd034]
[ 0.002409] Brought up 4 CPUs
[ 0.002422] SMP: Total of 4 processors activated.
[ 0.002428] CPU features: detected feature: 32-bit EL0 Support
[ 0.002434] CPU: All CPU(s) started at EL2
[ 0.002446] alternatives: patching kernel code
[ 0.003099] devtmpfs: initialized
[ 0.010388] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.015760] xor: measuring software checksum speed
[ 0.051980] 8regs : 2302.000 MB/sec
[ 0.092008] 8regs_prefetch: 2052.000 MB/sec
[ 0.132038] 32regs : 2830.000 MB/sec
[ 0.172068] 32regs_prefetch: 2379.000 MB/sec
[ 0.172072] xor: using function: 32regs (2830.000 MB/sec)
[ 0.172139] pinctrl core: initialized pinctrl subsystem
[ 0.172656] NET: Registered protocol family 16
[ 0.190248] cpuidle: using governor menu
[ 0.190605] Failed to initialise IOMMU /amba/smmu@fd800000
[ 0.190872] vdso: 2 pages (1 code @ ffffff80089c7000, 1 data @ ffffff8008e34000)
[ 0.190882] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.191334] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.201575] reset_zynqmp reset-controller: Xilinx zynqmp reset driver probed
[ 0.202306] ARM CCI_400_r1 PMU driver probed
[ 0.204834] zynqmp-pinctrl ff180000.pinctrl: zynqmp pinctrl initialized
[ 0.230479] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.296218] raid6: int64x1 gen() 406 MB/s
[ 0.364275] raid6: int64x1 xor() 442 MB/s
[ 0.432358] raid6: int64x2 gen() 673 MB/s
[ 0.500342] raid6: int64x2 xor() 599 MB/s
[ 0.568369] raid6: int64x4 gen() 983 MB/s
[ 0.636432] raid6: int64x4 xor() 739 MB/s
[ 0.704505] raid6: int64x8 gen() 1146 MB/s
[ 0.772524] raid6: int64x8 xor() 746 MB/s
[ 0.840568] raid6: neonx1 gen() 721 MB/s
[ 0.908592] raid6: neonx1 xor() 732 MB/s
[ 0.976680] raid6: neonx2 gen() 1166 MB/s
[ 1.044681] raid6: neonx2 xor() 1034 MB/s
[ 1.112746] raid6: neonx4 gen() 1506 MB/s
[ 1.180764] raid6: neonx4 xor() 1182 MB/s
[ 1.248818] raid6: neonx8 gen() 1585 MB/s
[ 1.316853] raid6: neonx8 xor() 1220 MB/s
[ 1.316857] raid6: using algorithm neonx8 gen() 1585 MB/s
[ 1.316860] raid6: .... xor() 1220 MB/s, rmw enabled
[ 1.316863] raid6: using intx1 recovery algorithm
[ 1.318205] SCSI subsystem initialized
[ 1.318372] usbcore: registered new interface driver usbfs
[ 1.318407] usbcore: registered new interface driver hub
[ 1.318441] usbcore: registered new device driver usb
[ 1.318499] media: Linux media interface: v0.10
[ 1.318522] Linux video capture interface: v2.00
[ 1.318546] pps_core: LinuxPPS API ver. 1 registered
[ 1.318550] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.318562] PTP clock support registered
[ 1.318583] EDAC MC: Ver: 3.0.0
[ 1.318839] FPGA manager framework
[ 1.318953] fpga-region fpga-full: FPGA Region probed
[ 1.319050] Advanced Linux Sound Architecture Driver Initialized.
[ 1.319326] Bluetooth: Core ver 2.22
[ 1.319347] NET: Registered protocol family 31
[ 1.319351] Bluetooth: HCI device and connection manager initialized
[ 1.319359] Bluetooth: HCI socket layer initialized
[ 1.319364] Bluetooth: L2CAP socket layer initialized
[ 1.319383] Bluetooth: SCO socket layer initialized
[ 1.319972] clocksource: Switched to clocksource arch_sys_counter
[ 1.320044] VFS: Disk quotas dquot_6.6.0
[ 1.320080] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.325923] NET: Registered protocol family 2
[ 1.326237] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 1.326441] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 1.326870] TCP: Hash tables configured (established 32768 bind 32768)
[ 1.326910] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.326985] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 1.327145] NET: Registered protocol family 1
[ 1.327363] RPC: Registered named UNIX socket transport module.
[ 1.327367] RPC: Registered udp transport module.
[ 1.327371] RPC: Registered tcp transport module.
[ 1.327374] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.327781] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.328428] futex hash table entries: 1024 (order: 5, 131072 bytes)
[ 1.328480] audit: initializing netlink subsys (disabled)
[ 1.328500] audit: type=2000 audit(1.324:1): initialized
[ 1.329024] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[ 1.329623] NFS: Registering the id_resolver key type
[ 1.329638] Key type id_resolver registered
[ 1.329642] Key type id_legacy registered
[ 1.329650] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.329666] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.333890] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 1.333897] io scheduler noop registered
[ 1.333901] io scheduler deadline registered
[ 1.333911] io scheduler cfq registered (default)
[ 1.334393] nwl-pcie fd0e0000.pcie: Link is DOWN
[ 1.334430] OF: PCI: host bridge /amba/pcie@fd0e0000 ranges:
[ 1.334446] OF: PCI: MEM 0xe0000000..0xefffffff -> 0xe0000000
[ 1.334454] OF: PCI: MEM 0x600000000..0x7ffffffff -> 0x600000000
[ 1.334553] nwl-pcie fd0e0000.pcie: PCI host bridge to bus 0000:00
[ 1.334561] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.334567] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 1.334573] pci_bus 0000:00: root bus resource [mem 0x600000000-0x7ffffffff pref]
[ 1.334858] pci 0000:00:00.0: PCI bridge to [bus 01-0c]
[ 1.336881] xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed
[ 1.337174] Write failed gate address:1000f02
[ 1.337258] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success
[ 1.337390] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success
[ 1.337518] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success
[ 1.337648] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success
[ 1.337785] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success
[ 1.337915] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success
[ 1.338045] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success
[ 1.338175] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success
[ 1.338351] zynqmp_pm firmware: Power management API v0.3
[ 1.365036] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.366520] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 39, base_baud = 6249999) is a xuartps
[ 2.339689] console [ttyPS0] enabled
[ 2.343749] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 40, base_baud = 6249999) is a xuartps
[ 2.352915] [drm] Initialized
[ 2.356121] [drm] load() is defered & will be called again
[ 2.362015] xilinx-drm-dp-sub fd4aa000.dp_sub: Xilinx DisplayPort Subsystem is probed
[ 2.369925] Unable to detect cache hierarchy from DT for CPU 0
[ 2.380056] brd: module loaded
[ 2.385649] loop: module loaded
[ 2.389445] ahci-ceva fd0c0000.ahci: couldn't get PHY in node ahci: -517
[ 2.396189] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.403902] m25p80 spi0.0: SPI-NOR-UniqueID 10000023536359160025001817101588af
[ 2.411047] m25p80 spi0.0: found n25q512a, expected m25p80
[ 2.416552] m25p80 spi0.0: n25q512a (131072 Kbytes)
[ 2.421387] 4 ofpart partitions found on MTD device spi0.0
[ 2.426842] Creating 4 MTD partitions on "spi0.0":
[ 2.431620] 0x000000000000-0x000000100000 : "qspi-fsbl-uboot"
[ 2.437823] 0x000000100000-0x000000600000 : "qspi-linux"
[ 2.443468] 0x000000600000-0x000000620000 : "qspi-device-tree"
[ 2.449643] 0x000000620000-0x000000c00000 : "qspi-rootfs"
[ 2.456147] libphy: Fixed MDIO Bus: probed
[ 2.461107] tun: Universal TUN/TAP device driver, 1.6
[ 2.466078] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.472353] CAN device driver interface
[ 2.478145] macb ff0e0000.ethernet: Not enabling partial store and forward
[ 2.485313] libphy: MACB_mii_bus: probed
[ 2.490960] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 23 (00:0a:35:03:6f:71)
[ 2.500712] TI DP83867 ff0e0000.etherne:0c: attached PHY driver [TI DP83867] (mii_bus:phy_addr=ff0e0000.etherne:0c, irq=-1)
[ 2.512389] usbcore: registered new interface driver asix
[ 2.517739] usbcore: registered new interface driver ax88179_178a
[ 2.523801] usbcore: registered new interface driver cdc_ether
[ 2.529615] usbcore: registered new interface driver net1080
[ 2.535257] usbcore: registered new interface driver cdc_subset
[ 2.541163] usbcore: registered new interface driver zaurus
[ 2.546726] usbcore: registered new interface driver cdc_ncm
[ 2.553916] usbcore: registered new interface driver uas
[ 2.559175] usbcore: registered new interface driver usb-storage
[ 2.565395] mousedev: PS/2 mouse device common for all mice
[ 2.571249] rtc_zynqmp ffa60000.rtc: rtc core: registered ffa60000.rtc as rtc0
[ 2.578421] i2c /dev entries driver
[ 2.583580] usbcore: registered new interface driver uvcvideo
[ 2.589241] USB Video Class driver (1.1.1)
[ 2.593786] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at ffffff800906e000 with timeout 10s
[ 2.602834] Bluetooth: HCI UART driver ver 2.3
[ 2.607195] Bluetooth: HCI UART protocol H4 registered
[ 2.612322] Bluetooth: HCI UART protocol BCSP registered
[ 2.617609] Bluetooth: HCI UART protocol LL registered
[ 2.622729] Bluetooth: HCI UART protocol ATH3K registered
[ 2.628112] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 2.634400] Bluetooth: HCI UART protocol Intel registered
[ 2.639780] Bluetooth: HCI UART protocol Broadcom registered
[ 2.645388] Bluetooth: HCI UART protocol QCA registered
[ 2.650625] usbcore: registered new interface driver bcm203x
[ 2.656266] usbcore: registered new interface driver bpa10x
[ 2.661827] usbcore: registered new interface driver bfusb
[ 2.667290] usbcore: registered new interface driver btusb
[ 2.672732] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[ 2.678418] usbcore: registered new interface driver ath3k
[ 2.683958] EDAC MC: ECC not enabled
[ 2.687601] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT)
[ 2.700544] sdhci: Secure Digital Host Controller Interface driver
[ 2.706640] sdhci: Copyright(c) Pierre Ossman
[ 2.710979] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.717983] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.724079] usbcore: registered new interface driver usbhid
[ 2.729565] usbhid: USB HID core driver
[ 2.736599] spi32766.0 supply vcc not found, using dummy regulator
[ 2.765819] axi_adxcvr 84a60000.axi-adxcvr-rx: cpll: fb_div_N1=5
[ 2.765819] cpll: fb_div_N2=4
[ 2.765819] cpll: refclk_div=1
[ 2.786876] axi_adxcvr 84a60000.axi-adxcvr-rx: cpll: fb_div_N1=5
[ 2.786876] cpll: fb_div_N2=4
[ 2.786876] cpll: refclk_div=1
[ 2.798937] axi_adxcvr 84a60000.axi-adxcvr-rx: AXI-ADXCVR-RX (16.01.a) using GTH4 at 0x84A60000 mapped to 0xffffff80090ac000. Number of lanes: 2.
[ 2.811972] axi_adxcvr 84a50000.axi-adxcvr-rx-os: cpll: fb_div_N1=5
[ 2.811972] cpll: fb_div_N2=4
[ 2.811972] cpll: refclk_div=1
[ 2.833269] axi_adxcvr 84a50000.axi-adxcvr-rx-os: cpll: fb_div_N1=5
[ 2.833269] cpll: fb_div_N2=4
[ 2.833269] cpll: refclk_div=1
[ 2.845585] axi_adxcvr 84a50000.axi-adxcvr-rx-os: AXI-ADXCVR-RX (16.01.a) using GTH4 at 0x84A50000 mapped to 0xffffff80090ae000. Number of lanes: 2.
[ 2.858870] axi_adxcvr 84a80000.axi-adxcvr-tx: qpll: fb_div=80, qpll: refclk_div=1
[ 2.866396] axi_adxcvr 84a80000.axi-adxcvr-tx: qpll: fb_div=80, qpll: refclk_div=1
[ 2.874048] axi_adxcvr 84a80000.axi-adxcvr-tx: AXI-ADXCVR-TX (16.01.a) using GTH4 at 0x84A80000 mapped to 0xffffff8009129000. Number of lanes: 4.
[ 2.888173] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered
[ 2.895050] xilinx-dp-snd-pcm dp_snd_pcm0: Xilinx DisplayPort Sound PCM probed
[ 2.902218] xilinx-dp-snd-pcm dp_snd_pcm1: Xilinx DisplayPort Sound PCM probed
[ 2.910745] Write failed to divider address:fd1a007c
[ 2.915789] xilinx-dp-snd-codec dp_snd_codec0: Xilinx DisplayPort Sound Codec probed
[ 2.923753] xilinx-dp-snd-card dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok
[ 2.933412] xilinx-dp-snd-card dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok
[ 2.943285] xilinx-dp-snd-card dp_snd_card: Xilinx DisplayPort Sound Card probed
[ 2.950685] pktgen: Packet Generator for packet performance testing. Version: 2.75
[ 2.958334] Netfilter messages via NETLINK v0.30.
[ 2.963059] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.968321] Initializing XFRM netlink socket
[ 2.972574] NET: Registered protocol family 10
[ 2.977354] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.982704] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.988881] NET: Registered protocol family 17
[ 2.993248] NET: Registered protocol family 15
[ 2.997675] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.010600] Ebtables v2.0 registered
[ 3.014199] can: controller area network core (rev 20120528 abi 9)
[ 3.020348] NET: Registered protocol family 29
[ 3.024763] can: raw protocol (rev 20120528)
[ 3.029004] can: broadcast manager protocol (rev 20161123 t)
[ 3.034649] can: netlink gateway (rev 20130117) max_hops=1
[ 3.040165] Bluetooth: RFCOMM TTY layer initialized
[ 3.044984] Bluetooth: RFCOMM socket layer initialized
[ 3.050105] Bluetooth: RFCOMM ver 1.11
[ 3.053834] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.059126] Bluetooth: BNEP filters: protocol multicast
[ 3.064339] Bluetooth: BNEP socket layer initialized
[ 3.069284] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.075188] Bluetooth: HIDP socket layer initialized
[ 3.080285] 9pnet: Installing 9P2000 support
[ 3.084482] Key type dns_resolver registered
[ 3.089428] registered taskstats version 1
[ 3.093977] Btrfs loaded, crc32c=crc32c-generic
[ 3.108123] PLL: shutdown
[ 3.110741] [drm] load() is defered & will be called again
[ 3.116743] xilinx-psgtr fd400000.zynqmp_phy: Lane:1 type:8 protocol:4 pll_locked:yes
[ 3.124706] xilinx-drm-dp fd4a0000.dp: device found, version 4.010
[ 3.130808] xilinx-drm-dp fd4a0000.dp: Display Port, version 1.0200 (tx)
[ 3.137748] xilinx-psgtr fd400000.zynqmp_phy: Lane:3 type:3 protocol:2 pll_locked:yes
[ 3.155604] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 3.164483] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
[ 3.174790] scsi host0: ahci-ceva
[ 3.178222] scsi host1: ahci-ceva
[ 3.181567] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 36
[ 3.189402] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 36
[ 3.198925] xilinx-psgtr fd400000.zynqmp_phy: Lane:2 type:0 protocol:3 pll_locked:yes
[ 3.228127] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.233537] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 3.241369] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x02010810
[ 3.250011] xhci-hcd xhci-hcd.0.auto: irq 225, io mem 0xfe200000
[ 3.256082] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.262784] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.269985] usb usb1: Product: xHCI Host Controller
[ 3.274846] usb usb1: Manufacturer: Linux 4.9.0-g6834429-dirty xhci-hcd
[ 3.281443] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 3.286589] hub 1-0:1.0: USB hub found
[ 3.290274] hub 1-0:1.0: 1 port detected
[ 3.294309] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.299716] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 3.307465] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 3.314175] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.321376] usb usb2: Product: xHCI Host Controller
[ 3.326237] usb usb2: Manufacturer: Linux 4.9.0-g6834429-dirty xhci-hcd
[ 3.332834] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 3.337948] hub 2-0:1.0: USB hub found
[ 3.341628] hub 2-0:1.0: 1 port detected
[ 3.346199] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 25
[ 3.352263] 0-0020 supply vcc not found, using dummy regulator
[ 3.358723] GPIO line 322 (sel0) hogged as output/low
[ 3.363892] GPIO line 323 (sel1) hogged as output/high
[ 3.369150] GPIO line 324 (sel2) hogged as output/high
[ 3.374403] GPIO line 325 (sel3) hogged as output/high
[ 3.379561] pca953x 0-0020: interrupt support not compiled in
[ 3.385299] 0-0021 supply vcc not found, using dummy regulator
[ 3.391654] pca953x 0-0021: interrupt support not compiled in
[ 3.398119] ina2xx 3-0040: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.404790] ina2xx 3-0041: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.411464] ina2xx 3-0042: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.418142] ina2xx 3-0043: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.424813] ina2xx 3-0044: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.431486] ina2xx 3-0045: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.438159] ina2xx 3-0046: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.444833] ina2xx 3-0047: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.451514] ina2xx 3-004a: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.458180] ina2xx 3-004b: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.464465] i2c i2c-0: Added multiplexed i2c bus 3
[ 3.469827] ina2xx 4-0040: power monitor ina226 (Rshunt = 2000 uOhm)
[ 3.476498] ina2xx 4-0041: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.483163] ina2xx 4-0042: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.489834] ina2xx 4-0043: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.496509] ina2xx 4-0044: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.503268] ina2xx 4-0045: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.509938] ina2xx 4-0046: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.510174] ata1: SATA link down (SStatus 0 SControl 330)
[ 3.510199] ata2: SATA link down (SStatus 0 SControl 330)
[ 3.527374] ina2xx 4-0047: power monitor ina226 (Rshunt = 5000 uOhm)
[ 3.533660] i2c i2c-0: Added multiplexed i2c bus 4
[ 3.546476] random: fast init done
[ 3.572292] i2c i2c-0: Added multiplexed i2c bus 5
[ 3.577141] i2c i2c-0: Added multiplexed i2c bus 6
[ 3.581850] pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544
[ 3.589802] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 26
[ 3.596529] at24 7-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
[ 3.603164] i2c i2c-1: Added multiplexed i2c bus 7
[ 3.608127] i2c i2c-1: Added multiplexed i2c bus 8
[ 3.614874] si570 9-005d: registered, current frequency 300000000 Hz
[ 3.621162] i2c i2c-1: Added multiplexed i2c bus 9
[ 3.626003] usb 1-1: new low-speed USB device number 2 using xhci-hcd
[ 3.646237] si570 10-005d: registered, current frequency 148500000 Hz
[ 3.652611] i2c i2c-1: Added multiplexed i2c bus 10
[ 3.657655] i2c i2c-1: Added multiplexed i2c bus 11
[ 3.662583] i2c i2c-1: Added multiplexed i2c bus 12
[ 3.667508] i2c i2c-1: Added multiplexed i2c bus 13
[ 3.672427] i2c i2c-1: Added multiplexed i2c bus 14
[ 3.677227] pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548
[ 3.685076] i2c i2c-1: Added multiplexed i2c bus 15
[ 3.691093] at24 16-0050: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 3.697728] i2c i2c-1: Added multiplexed i2c bus 16
[ 3.702725] i2c i2c-1: Added multiplexed i2c bus 17
[ 3.707976] i2c i2c-1: Added multiplexed i2c bus 18
[ 3.712909] i2c i2c-1: Added multiplexed i2c bus 19
[ 3.717842] i2c i2c-1: Added multiplexed i2c bus 20
[ 3.722768] i2c i2c-1: Added multiplexed i2c bus 21
[ 3.727701] i2c i2c-1: Added multiplexed i2c bus 22
[ 3.732497] pca954x 1-0075: registered 8 multiplexed busses for I2C switch pca9548
[ 3.783705] usb 1-1: New USB device found, idVendor=413c, idProduct=301a
[ 3.790322] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.797436] usb 1-1: Product: Dell MS116 USB Optical Mouse
[ 3.802904] usb 1-1: Manufacturer: PixArt
[ 3.806993] mmc0: SDHCI controller on ff170000.sdhci [ff170000.sdhci] using ADMA 64-bit
[ 3.815388] adrv9009 spi32766.1: adrv9009_probe : enter
[ 3.826238] axi_adxcvr 84a80000.axi-adxcvr-tx: qpll: fb_div=40, qpll: refclk_div=1
[ 3.842829] axi_adxcvr 84a50000.axi-adxcvr-rx-os: cpll: fb_div_N1=5
[ 3.842829] cpll: fb_div_N2=2
[ 3.842829] cpll: refclk_div=1
[ 3.855011] adrv9009 spi32766.1: ADIHAL_resetHw at index
[ 3.869249] input: PixArt Dell MS116 USB Optical Mouse as /devices/platform/amba/ff9d0000.usb0/fe200000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1:1.0/0003:413C:301A.0001/input/input0
[ 3.884889] hid-generic 0003:413C:301A.0001: input: USB HID v1.11 Mouse [PixArt Dell MS116 USB Optical Mouse] on usb-xhci-hcd.0.auto-1/input0
[ 4.116128] mmc0: new ultra high speed DDR50 SDHC card at address aaaa
[ 4.122789] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
[ 4.131807] mmcblk0: p1 p2 p3
[ 4.572980] random: crng init done
[ 11.594056] adrv9009 spi32766.1: adrv9009_probe: adrv9009 Rev 192, Firmware 4.0.4 API version: 3.4.0.0 successfully initialized
[ 11.616553] cf_axi_dds 84a04000.axi-adrv9009-tx-hpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.00.b) at 0x84A04000 mapped to 0xffffff800930c000, probed DDS AD9371
[ 11.631257] PLL: enable
[ 11.633806] PLL: shutdown
[ 11.636497] OF: graph: no port node found in /xilinx_drm
[ 11.641728] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 11.648323] [drm] No driver support for vblank timestamp query.
[ 11.676976] PLL: enable
[ 11.701171] Console: switching to colour frame buffer device 128x48
[ 11.714326] xilinx-drm xilinx_drm: fb0: frame buffer device
[ 11.739981] [drm] Initialized xilinx_drm 1.0.0 20130509 on minor 0
[ 11.766479] cf_axi_adc 84a00000.axi-adrv9009-rx-hpc: ADI AIM (10.00.b) at 0x84A00000 mapped to 0xffffff8009620000, probed ADC ADRV9009 as MASTER
[ 11.779671] input: gpio-keys as /devices/platform/gpio-keys/input/input1
[ 11.786478] rtc_zynqmp ffa60000.rtc: setting system clock to 2018-05-16 12:36:43 UTC (1526474203)
[ 11.796457] ALSA device list:
[ 11.799331] #0: DisplayPort monitor
[ 12.036663] EXT4-fs (mmcblk0p2): recovery complete
[ 12.044184] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 12.052215] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 12.062580] devtmpfs: mounted
[ 12.065577] Freeing unused kernel memory: 512K (ffffffc000db0000 - ffffffc000e30000)
Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory
[ OK ]ting up X socket directories...
* STARTDISTCC is set to false in /etc/default/distcc
* /usr/bin/distccd not starting
[ OK ]rting IIO Daemon iiod
Last login: Tue May 15 07:20:04 UTC 2018 on tty1
Welcome to Linaro 14.04 (GNU/Linux 4.9.0-g6834429-dirty aarch64)
* Documentation: https://wiki.analog.com/ https://ez.analog.com/
user@analog:~$
~$
iio_attr -d
iio:device0: xlnx,versal-sysmon
iio:device1: hmc7044
iio:device2: axi-ad9084-rx-hpc (buffer capable)
iio:device2: axi-ad9084-rx-hpc-b
iio:device3: axi-ad9084-tx-hpc (buffer capable)
iio:device3: axi-ad9084-tx-hpc-b